Jump to content
SAU Community

Recommended Posts

Hi everybody,

This is gear I didn't even know I had, but need it all cleared out ASAP. I think it is all pretty cheap as I want to move it all on, but if you don't think so just make a reasonable offer. I can organise postage for everything (except tyres) at buyer cost.

- R33 GTR OEM ABS unit $50.00

- R33 GTR OEM washer bottle and bracket $20.00

- OEM low mount turbo manifolds $40.00 (x2 sets available one from R32 GTR and one from R33 GTR)

- R32 GTR OEM rear axles/driveshafts $200.00

- R33 GTR OEM front tailshaft $50.00

- R33 GTR OEM 'Twin Turbo' pipe $20.00

- R33 GTR OEM turbos and dump pipes $100.00 (perfect condition, never boosted more than 11psi as removed from my R33 GTR at roughly 100,000km)

- R33 GTR OEM complete wiring loom $100.00 (body, engine, fuse box... complete removed from running car!)

- R33 GTR OEM pedals, brake, clutch, accelerator $15.00, $15.00, $10.00 respectively

- R33 GTR OEM swaybars front and rear $20.00 each

- R32 GTR Atessa pump unit $50.00 (was removed from running car)

- Tyres Mazzini ECO605 size 255/35R18 with some tread left see photos $60.00 a pair ($100.00 for all four)

Can get more pictures on request. Just text me if you want details or are interested in any items.

Thanks,

Mike 0456969001

20180319_164630.jpg

20180319_164656.jpg

20180319_164738.jpg

20180319_165106.jpg

20180319_165513.jpg

20180319_170013.jpg

20180319_170032.jpg

20180319_170051.jpg

20180319_170119.jpg

20180319_170251.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...