Jump to content
SAU Community

Recommended Posts

Hi all, 

Looking at moving from nz to western Australia and bringing my s14 200sx with me. I'm pretty sure nz got the same spec 200sx but without the ADR tags. So, I'll need to fit a high flow cat? Of do I wait until it arrives in strata for this? What's the go with minor panel damage? She's had a bit of a hard life nothing structual just dented guards.do I need to get it panel beaten or would it be OK? I'm assuming a rear fibreglass bumper and missing front bumper reinforcement would be a problem but I'll get that sorted. Last things are I have a hks ssqv bov that vents externally which I believe is illegal in oz? I can get an adaptor and reroute it into the air intake if neccesary. And I have a hole in the battery tray- battery's in the boot- for the intercooler piping. I plan on welding in a section of steel with a pressed factory hole I cut off a wreck so it looks factory. 

I appreciate any input cheers andrew

IMG_20180520_100858.jpg

Yea I was gonna get a shipping container and pack some other shit around it. I realise it would likely be cheaper to sell it and buy a similar car in oz but it used to be my little brothers car he passed away a few years ago so it has the emotional attachment happening. 

I suggest you talk to an import broker before you spend any money fixing things.  Personal imports fall under different and more open rules than normal. Try Geoff at Prestige Motorsport or Kristian at Iron Chef Imports

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...