Jump to content
SAU Community

Recommended Posts

Hi all, 

So this is somewhat of a noob question, and  after much searching SAU, FB, and the interwebs, i cannot find any concrete info on how to reset the TPS position on an RB25 neo. Some background on why i need to do this: I had been chasing an electrical gremlin where the car would die after hitting the limiter( which turned out to be an incorrectly set Nistune rev limit parameter). During the whole process, i had checked the TPS voltages, and noticed that when the TPS was closed it read 0.30v, and at WOT it would read 3.63v. The resistance sweep in both directions was correct.

Now, obviously this is out of Nissans specified window, and when i try to adjust it, it just idles up (to about 2000rpm) and the TPS IDLE indicator in Nistune does not illuminate, and adjusting the IACV does nothing to reduce the RPM. I've read you could leave the battery disconnected, or cycle the ign on and off 10 times etc etc but none of these have worked. The only thing i have yet to check (which i should have done earlier) is to refit my original Neo auto TB, which i had swapped over to an S2 RB25 TB (because the TSC TB solenoid fouled on my coilpacks), my thinking here is that maybe the S2 TB doesnt open/sweep the same way as the Neo? (im still using the neo TPS)

Anyone with any tips? Much appreciated. 

Link to comment
https://www.sau.com.au/forums/topic/474514-rb25det-neo-tps-resetrelearn/
Share on other sites

  • 4 months later...

So I dont have nistune, I just have a enathply tune, I have the two throttle bodys, a billet q45 throttle body. Am have a code 46 throttle motor sensor. Would this after the driveability of the car? Also how are yall running the tps sensors on the neo with a q45?

Throttle motor sensor is NOT anything to do with the TPS.  It is to do with the traction control throttle's position sensor.  You will get that code (in the ECU) if the TCS system is not working (is, if the TCS computer is not present, or the TCS throttle is broken in some way).

We don't make TPS sensors work with Q45 throttles on NEOs, because, um, we don't change the TB.  Why would we?  The stocker is big enough for everything.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...