Jump to content
SAU Community

Precision 6266,Trust T78-29D,NPC push clutch,BPP fuel rail,32 N1 bootlips,Turbosmart FPR800 fuel reg,R32/R33 GTR blow off valves,GTR front diff centre,1000cc injectors


Recommended Posts

Nothing, except the Quaife rear diff centre of course. Bolts up to any GTR driveshaft axles, except R33 and R34 v spec active diff shafts as they are shorter. Any GTR non active diff driveshafts will bolt up, correct length. This is my spare set I don't need and used same setup. Installed it on my 32 earlier this year when I put Quaife front and rear diffs in.

2 minutes ago, BK said:

Nothing, except the Quaife rear diff centre of course. Bolts up to any GTR driveshaft axles, except R33 and R34 v spec active diff shafts as they are shorter. Any GTR non active diff driveshafts will bolt up, correct length. This is my spare set I don't need and used same setup. Installed it on my 32 earlier this year when I put Quaife front and rear diffs in.

So the diameters of the shafts are the same and will just fit into the old 32 housing no problems?

Who did you use to install the diffs? If you dont mind me asking, since Award is no longer.

There is a 1mm diameter increase in non splined shaft area from 32mm (30 tooth) to 33mm (31 tooth) and 1mm approx. increase in diameter on spline from 30.9mm (30 tooth) to 32mm (31 tooth). No problems with housing clearance as the increase is all to do with the diff centre bigger spline change. The speed sensor 46t outer and 6 x 1 flange pattern and dimensions are the same.

My father who is a mechanic and has his own workshop did the diff install. Don't have the luxury of 100s of workshops here in Alice Springs like on the east coast. He's pretty much the resident RB26 / GTR guru here in town. Not a lot he doesn't know about them or how to work on them. He is the assembler of the OS giken box for sale here also.

Full genuine Nissan RB26 exhaust / turbo side gasket set - SOLD

Tomei RB26 metal exhaust manifold gaskets - SOLD

  • 4 weeks later...
  • 3 weeks later...

Nismo thermostat - SOLD

Nismo radiator cap - SOLD

Tomei block restrictor - SOLD

ATS clutch discs and pressure plate sold pending payment.

31t rear half shafts sold pending payment.

All PMs replied to.

Fresh 10 plate (standard is 7) modified transfer case is now completed and up for sale. Like new inside and reset back to factory new tolerances. New drive / friction plates, new strainer filter, new oil pump o rings, new retaining and pressure plates, shimmed back to factory 0.2mm - 0.5mm (8 - 20 thou) drum clearance as per required tolerance (around 13 thou from memory).

$1500

Just added for sale Trust / Quaife 3F1 6 speed H pattern straight cut dog box with freshly modified transfer case added for sale.

$8500 ONO shipped anywhere (possibly throw a clutch in there with it with the right buyer).

Going sequential so not needed - make and offer !

WP_20190213_17_31_16_Pro.jpg

WP_20190213_17_31_04_Pro.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
    • Thanks guys - I have been overseas for a hectic many weeks , so haven't had time to chase any of these up.  Some of the suggestions are for 4.1 ratio, which I already have, and a 3.5 at Lonsdale, which is also too tall.  Really looking for 3.9 or even a 3.7 LSD, either with M12 bolts. Will look some more.  
×
×
  • Create New...