Jump to content
SAU Community

Recommended Posts

So the problem I'm having is that my stock boost gauge on my mdf screen is reading 0.6 bars at idle. I started having the problem after i replace my throttle body and intake manifold gaskets and slightly cleaned my throttle body. I know i shouldn't have cleaned them but i stopped after i read that you shouldn't but my idle isn't high at all. Only problem I'm having is the guage reads boost at 0.6 bars at idle.  i also have a greddy profec that reads -0.5 bars at idle thats hooked up to a mac controller. The controller is hooked up with one hose to the intake plenum near the idle air control valve and the other on is somewhere's else. Its really hard to see and i didn't add the controller or greddy. It was on there from the previous owner. Please help, I'm stumped and don't know what else to do. I'm new to this so please go easy on me...thanks in advance.

Edited by hybridracer504
Link to comment
https://www.sau.com.au/forums/topic/476600-r34-rb26dett-boost-issue/
Share on other sites

That is a bit strange, because that just comes from the MAP sensor on the firewall near the brake master cylinder.

Does it work OK when you start to hit boost (ie, does it match the greddy gauge when you are driving)?

I'd start with swapping the MAP sensor for another one to see if it has failed somehow, otherwise there may be some issue in the wiring. The air source is unlikely to be the issue since it is reading high, but you can check the air line is connected to the back of the plenum and has no cracks or splits

2 hours ago, Duncan said:

but you can check the air line is connected to the back of the plenum and has no cracks or splits

Is not the GTR boost gauge MAP sensor supposed to be connected to the little plenum that taps into the intake runners downstream of the throttle plates?  How would it ever read vacuum if it were not?

57 minutes ago, GTSBoy said:

Is not the GTR boost gauge MAP sensor supposed to be connected to the little plenum that taps into the intake runners downstream of the throttle plates?  How would it ever read vacuum if it were not?

Agreed....it should be on the manifold (post throttle), not plenum (pre throttle)! Been too long since I've run with one attached. Either way it is not clear to me how it could read higher than atmo unless the problem was electrical not mechanical

I don’t know...it was working fine before I replaced the gaskets. The greddy profec is tapped into the same vacuum line as the sensor. I’ve unplugged the vacuum line for the greddy and it still doesn’t change. I’ve tried driving it down the street but I’m afraid to get on it. Both of the gauges read different. The stock one on the vehicle spikes all the way to 1.2 bars when I tap on the accelerator. What are the ohm readings for checking that sensor? I just don’t want to throw parts at it and not fix the problem 

Edited by hybridracer504

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...