Jump to content
SAU Community

R33 GTST 4 pot calipers

GTSBoy
 Share

Recommended Posts

GTSBoy Grand Master

GTSBoy

Posted
Posted

R33 GTST 4 piston / spot / pot calipers.

In good working order. Came off my car working, removed due to an upgrade. Still wet with fluid inside. Seals look good. Have been stored wrapped in plastic in a box in the shed.

Complete with pins, shims and cross springs. All good, just need a clean. The short hard lines are attached. I have OEM rubber lines for and R32 if you need. Also removed from my car working, as part of the upgrade.

I have some ~50% used stock (or maybe Bendix Ultimate) type pads that will suit, if you need. No charge.

I have matching 296mm rotors if you're desperate. But they are only just over 28mm thick and will likely go below minimum if they're skimmed. Not worth shipping these anywhere - better off putting the money towards new rotors.

Asking $300 shipped in Australia. Polite offers considered.

IMG_5906crsm.jpg

IMG_5907crsm.jpg

Link to comment
https://www.sau.com.au/forums/topic/478862-r33-gtst-4-pot-calipers/
Share on other sites
  • 7 months later...
  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a good German place in Brisbane if youre up for the drive 😛
    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
×
×
  • Create New...