Jump to content
SAU Community

LHS Headlight No Power - R32 GTS-T

Strexx

By Strexx,
in Car Audio & Electrical

 Share

Recommended Posts

Strexx Enthusiast

Strexx

Posted
Posted

So my LHS headlight (Projector) is not working but my RHS headlight (Projector) is.  But both of the adjacent lights are not working.  For now I am trying to work out why the LHS Projector is not working.

  • The lamp is brand new
  • The lamp is seated correctly in the metal frame with the clip holding it in place
  • When I test with a 12V lamp circuit tester - I get no voltage whatsoever at the connector!! when I pull put the cables going to the headlight
  • I've checked the 15amp fuses in the engine bay - visually they look fine, but even with a multi meter they are testing OK.
  • I pulled out the relay in the engine bay and reseated it again.

Can anyone advise how to:

A - Test the relay to see if the fault is here

B - Advise what else could be causing the fault

 

My next problem is the adjacent lights to the projector lamps on both sides - Why would these not be working and ideas?

Thanks in advance.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      R32 Gtr Long Term Love, Now Project

      By PranK · Posted

      Me too. Apparently the new version of Invision will allow some customisation so look forward to a 'Love' reaction and a new 'Like' icon.
    • WMDC35
      rb20de neo +t conversion - boost pressure sensor needed?

      By WMDC35 · Posted

      Which injectors are you using? It's likely the fuelling is off also, so as above.
    • LjB123
      R34 Series 1 And 2 Front Reo Difference?

      By LjB123 · Posted

      Awesome to know. I have a Series 1, and When pulling my front bumper off for the first time i realised my reo/crash bar was a bit worse for wear, and was going to try pick up a better one soon just so i can replace it. Someone is selling a full series 2 front bar and brackets for a decent price, so was going to probably reuse my brackets and install the new second hand reo/crash bar. I also have a genuine Altia body kit to do up, spray and put on, and not sure if that will use the series 1 or series 2 brackets for the front bumper, so having both will be handy, and knowing i can drill holes out to make stuff fit between series is also handy to know!
    • Kinkstaah
      R34 Series 1 And 2 Front Reo Difference?

      By Kinkstaah · Posted

      I should also say that the while they are different the only parts that matter are the center headlight supports and center bar from S1 to S2. The center bar will work, but the S1 has holes that clips go through into the S1 bumper. So if you were super cheap you could simply drill the S2 bar. Same thing with the side/wings. They have slightly different 'clips' but can be made to work. The center headlight brackets however, cannot. This is also where the GTR differs, which has a different center bar, and different headlight supports (to either GTT system), it also has different 'wing' headlight supports which is what I am calling under the headlight. However those CAN be made to work with the GTT Reo for a GTR front bar by a small spacer and a drill/tapping a thread into the reo because the bolt positions are slightly different. So people only really need the center brackets to go between GTT S1, GTT S2, and GTR if you are happy to do some tinkering.
    • dbm7
      forum.r31skylineclub.com down or gone?

      By dbm7 · Posted

      Indeed  😃  Appears the site is back up now (migrated not updated) - kudos @funkymonkey & @PranK
×
×
  • Create New...