Jump to content
SAU Community

Recommended Posts

Hey team. 
 

Bit of a noob question.  I have to take my 34 to an auto sparky to get a couple of bits n pieces sorted out. 
 

Ive notice that the car seems to run a bit sluggish and smells a bit rich. I used to have an S14 which was also only an NA 2L auto but that seemed to have a lot more go than my 34. 
 

would checking the tune/ timing etc be something they would do or would that be more of a mechanic thing. 
 

cheers in advance. 

Link to comment
https://www.sau.com.au/forums/topic/479780-checking-my-tune/
Share on other sites

Hey mate,

What ECU does your car have? If it's a stock ECU, what do you think someone is actually doing when you say 'check the tune'? 

As for checking your timing, do you mean throwing a timing light on it and checking the base timing is correct? Virtually anyone should be able to do that for you. 

What things have you done so far to try and fix the running rich issue?

Checking the tune I wasn’t sure if shit could get outta whack or anything. The timing I wasn’t sure if you could use a light or not as I’ve read a few things mentioning that a light wouldn’t work for some reason. As for running rich all I’ve done so far is plugs, coils and had to replace maf sensor cos that kacked itself. Not sure if any of those would help tho.
 

Cher’s for your reply

You can't change the tune with a stock ecu but a garage could test your exhaust for AFRs to see if it really is excessively rich. Timing can certainly be checked with a timing light but it is unlikely to be your problem.

10 hours ago, Hazzid69 said:

Checking the tune I wasn’t sure if shit could get outta whack or anything. The timing I wasn’t sure if you could use a light or not as I’ve read a few things mentioning that a light wouldn’t work for some reason. As for running rich all I’ve done so far is plugs, coils and had to replace maf sensor cos that kacked itself. Not sure if any of those would help tho.
 

Cher’s for your reply

Could still be as simple as an oxygen sensor or boost leak. 

Also, you could pay $80-$150 and throw it on a dyno to check your AFRs. You might find the fuel smell is actually a fuel leak somewhere and the feeling sluggish, is just your butt-dyno isn't properly calibrated lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...