Jump to content
SAU Community

Recommended Posts

Hi everyone, 

I recently bought a 2nd hand Nismo 320km/h cluster for my R32 GTR. I understand that there are two versions, one for earlier series 32, and another for the later 32's. The seller assured me it was working 100% in an early model (1990) R32 GTR, which is the same as mine.

I installed it yesterday, it fit perfectly, and all the plugs in the back went in fine - but when using the car, the temperature gauge doesn't work and the RPM doesn't work either. The speed reading works and is perfectly accurate, but power steering stops working shortly after.

It's also the blue-back one, with 4 screws at the back of the speedo; this all suggests that it's for a later model as well, where the electrical signal for speed for the power steering is different.

I've seen a tutorial on here about swapping the speed sensor over from an old cluster, but is there any reason that the temperature gauge doesn't work as well? Are there any other differences on the later cluster that mean I shouldn't waste my time trying to use it in an older GTR at all?

87008640_1699112463559905_1341501247852642304_n.jpg

Edited by californianhunger
Link to comment
https://www.sau.com.au/forums/topic/479864-nismo-320-cluster-in-r32-gtr-issues/
Share on other sites

I was not aware of an electrical difference, just cosmetic between series 1 and 2....I'd start with checking if temperature, rpm and speed (out) are all on the same plug that was not seated properly when you put it back in. The speedo itself is mechanical and is often installed incorrectly onto the cable (sounds like yours is OK), but the dash provides the speed signal conversion for the ECU and probably HICAS.

Also, when you say power steering stops woking, I assume you mean you get less assistance, not none at all. If HICAS gets no speed signal it gets heavier but you should still have some power assist; I run mine without the speed signal at all times and find it OK.

23 minutes ago, GTSBoy said:

There is an electrical difference. Well, there's no actual electrical difference as far as I know - it's just wiring pinouts. The speed signal out to the ECU is the same PWM. etc.

I think something is different, not sure what, but this guide exists to swapping that analog to digital bit in the speedo cluster: 

That's something I could do, but doesn't answer why RPM and temp are not working.

32 minutes ago, Duncan said:

I was not aware of an electrical difference, just cosmetic between series 1 and 2....I'd start with checking if temperature, rpm and speed (out) are all on the same plug that was not seated properly when you put it back in. The speedo itself is mechanical and is often installed incorrectly onto the cable (sounds like yours is OK), but the dash provides the speed signal conversion for the ECU and probably HICAS.

Also, when you say power steering stops woking, I assume you mean you get less assistance, not none at all. If HICAS gets no speed signal it gets heavier but you should still have some power assist; I run mine without the speed signal at all times and find it OK.

Yeah much less assistance. I would prefer to have the power steering working properly, the fix for that is in the link above. I'm going to try and re-seat the connector. I'm hoping it's as simple as that, but I doubt it ?

I cannot imagine that it is necessary to actually swap the speed sensor. As I said, the speed signal should be exactly the same on both early and late 32s. That being a 0-5v square wave PWM. It's all shown in the R32 GTR manual. It must just be a matter of which pins it's all wired to.

I compared the back of both original and Nismo clusters are there were quite a few differences.

FWIW, I just put the Nismo 320 speedo in to my old dash, and converted speed sensor plug thingie with this guide:

All works fine now...

Edited by californianhunger

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...