Jump to content
SAU Community

Recommended Posts

G'day guys,

Just purchased a 32GTR, it has some basic oil restriction mods and other power mods. It's on 143km's.
I'm looking to refresh all the fluids before I drop it in for a tune at the end of the month. 
There's a lot of info online about this topic but a lot of it is historical(up to 15 years old). There aren't any recent posts(that i can find) that address the topic.

My research has lead me to pick these fluids :

Gearbox oil: Redline Heavy Shockproof Gear oil  - 4.5 L

Front diff : Redline Lightweight Shockproof Gear Oil - 1L

Rear diff: Not sure??

Brake fluid: Nulon xtreme performance gear oil. dot 4

Power steering fluid : Castrol DEX III Automatic Transmission Fluid 1 Litre

Transfer case : Nissan Matic D transmission fluid

Engine oil: Not sure??

Don't put Shockproof in anything unless you need it because of crunchy selectors. For f**k's sake, don't put it in the front diff. Use diff oils in diffs. A good LSD oil for the rear, a normal (non-LSD) diff oil for the front, unless it has had an LSD centre put in it.

Thanks for the replies guys! think i figured it out.

 

On 04/11/2020 at 9:35 PM, E33 said:

if you got gearbox selector issues - shock proof aka -  smurfs blood 

Down load the penrite app and use the recommended oils 

Good old australian made stuff 

I'm a bit concerned that they recommend the same oil for front and rear diff when a lot of people online say don't use the same oil(due to lsd and non lsd)

On 05/11/2020 at 11:29 AM, GTSBoy said:

Don't put Shockproof in anything unless you need it because of crunchy selectors. For f**k's sake, don't put it in the front diff.

Decided to shockproof heavy the gearbox. But not the diff
 

There is no reason to use shockproof in a healthy gearbox ever. Absolutely none. A 75w - 85 GL-4 provides the smoothest shifts with the brass synchros. Even GL-5 at 75w-90 is noticeably worse in the upper rev range shifting. Shockproof is gummy crap that sticks to everything and if you've ever pulled a box down you'd never recommend it. It masks synchronisation wear and is about the same result as using a normal oil and adding a shift additive like that Nulon or Penrite smooth shift crap - the oil becomes a paste.

LSD or not the LSD oil is fine for the open fron diff, it's just not required, but the best synthetic heavier weight oils are mostly LSD oils by design though. As I've said repeatedly in the paat the stock front diff oil weight is retarded - way too light, so use an 80 or 90 weight oil in front diff at your own risk. 75w-140 in both front and rear if you want to retain healthy crown wheel and pinions on you GTR diffs is the go.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day  
    • While I was waiting for the new parts to come in for the charge pipe and radiator I decided to do some turbo modification. The drive pressure (exhaust backpressure) was a lot higher that I thought it should be. For 32lbs of boost drive was 55lbs. The turbine housing is a 1.10AR and my turbo builder has suggested to go to a 1.25AR. To test if a larger AR would do anything to reduce drive pressure AND not spend any money I decided to hog out the divider in my current housing. I removed it from the inlet and the whole way through the housing.  After reassembly and testing it doesn't look like this modification did anything for reducing drive pressure or requiring more fuel (making more power). Oh well, it was worth a shot. We'll get some data at the track if it makes it past the 60ft. I also machined a $7 shift knob off Amazon to fit my Stillway shifter since I didn't like the Stillway shift knob. Next on the list was the radiator replacement and fabrication of a new intercooler tube that had no silicon coupler. No pictures of this - I was short on time each night after work to get this done and didn't stop to take pictures.  Next was to get the clutch disks out and replaced. Previously when installing the dogbox I had ordered a set of the same sintered iron disks I had been running because I switched to the 26-spline input shaft. I thought it was odd that they didn't have any markings or brand name on them like all my old disks had but installed them anyway. At the track I could not get the clutch to lock up using my normal strategies. After two track nights I reached out to the clutch manufacturer and ask their thoughts. They said they had to switch the material out because they were having trouble getting the original material and that this new material would not take to being slipped very well.  So out with the first set of 26-spline disks and in with the correct material 26-spline disks. While I had the trans out I added an inspection/service hole. I've wanted one of these for a while. Now I can have a look at things and change the front cover shimming when needed (clutch wear). I hustled and got the clutch change done in a few hours on a Saturday. Hopped in the car and drove home. On the way home I did a 1-3 pull. When shifting from 2nd to 3rd the core plug in the back of the cylinder head popped out and dumped all the coolant. Thankfully I was only 30 seconds from home and coasted it there. Datalog showed nothing unusual and 2.5psi of coolant pressure. That plug has been in there since 1992 but I guess it worked its way out. Pulled the trans AGAIN and replaced the plug, JB welded it in, and made a brace. Also deleted the head drain I had added in during the bearing issue fiasco.  I am currently changing my boost control plumbing to make it cleaner. After that is done I'll make another attempt at getting past the 60.
    • Are you 100% sure this isn't tune related?
    • 140-150 across the board. At this point hoping the grounding harness fixes it. My grounds are all tied to the chassis and none to the battery. For SR and KA that’s never been a problem for me but had a few other guys here and Reddit who told me RB really like a very solid ground setup tied to the battery so going to try that next, I’m stumped if that doesn’t do it. Never had a car have spark and fuel and not fire off before. Only thing I can think is the spark is intermittent/weak because of grounds nothing else really makes sense at this point 
    • I am having close to the same issue. Can you help me with what wire you grounded to get your pump to trigger?
×
×
  • Create New...