Jump to content
SAU Community

Recommended Posts

With different piston and rod sizes...

http://babelfish.altavista.com/babelfish/t...dett27rkit.html

Its good to find a use for all the years in school.

How exactly do you increase stroke by 2mm with a piston upgrade on standard crank? :confused:

And I don't need a web calculator, I remember my Year 7 volumetric formulas :Oops: Probably the first time I've used them since high school :)

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

And the rings were properly seated and in full seal?

Adrian is right.

Synthetic is not a recommended run in oil.

These 2.7 and HKS 2.8 kits are ok for drag purposes and perhaps if they kit if cheap, go for it instead of your plain forged but until it gets to the OS Giken 3.0 litre set, I doubt that there's that much difference.

Maybe a bit more meaty torque in the middle?

T.

Yep, you read right. 5000km.

I can't imagine running 1.9 bar of boost on a new engine that has only done 1,500km.

Even if the engine was standard, I still wouldn't tune it to full power till at least 5,000km.

After spending over $10,000 on the engine, 5,000km is nothing mate.

5000km run-in??? That would take most people 6 months to complete. You really think that's a feasible run-in time?

What engine parts could POSSIBLY need 5000kms bedding in time??? :uhh:

No comment on the full-synthetic running in oil use... People have different ideas on that one, but the vast majority believe that mineral oil for the first 1000kms or so is still the best way to go.

You'll have to tell tuning shops like Top Secret, Still Way, Veilside etc. that it doesn't make much difference. Most of those tuners build track and high speed cars.

Regarding oils,

The less friction on an engine the better.

Adrian is right.

Synthetic is not a recommended run in oil.

These 2.7 and HKS 2.8 kits are ok for drag purposes and perhaps if they kit if cheap, go for it instead of your plain forged but until it gets to the OS Giken 3.0 litre set, I doubt that there's that much difference.

Maybe a bit more meaty torque in the middle?

T.

With different piston and rod sizes...

http://babelfish.altavista.com/babelfish/t...dett27rkit.html

 

Its good to find a use for all the years in school.

But you just linked me to the GREX stroker kit, and that's not what you have...

It's the crank in the GREX stroker kit that gives it the extra 2mm stroke, not the pistons or rods :P

And yes, I was pretty proud of myself that I remembered how to calculate volume of a cylinder without looking it up :) :Oops:

My kit isn't the stroker kit, it's the 2.7 ltr kit.

The stoker kit comes with the crank which I didn't get.

But you just linked me to the GREX stroker kit, and that's not what you have...

It's the crank in the GREX stroker kit that gives it the extra 2mm stroke, not the pistons or rods :D

And yes, I was pretty proud of myself that I remembered how to calculate volume of a cylinder without looking it up :D :Oops:

I cracked my old block in 4 places.

Id prefer to leave the extra 1mm bore thickness in the block and get a realible 7-800hp than boring it to 1mm of its life and drastically reducing the blocks rigidity . Have seen a block split at high horsepower with 88mm bore.

I don't think a thicker block gives you realibility.

If the block is going to crack, I honestly don't think 1mm is going to save you.

I've seen pistons and rods go through the side of a block with a standard sized bore due to spinning bearings.

As you may know, RB26 engines are renowed for spinning bearings which in turn will damage all kinds of things in the engine including the engine block.

I think it's the package that will give you realiablity.

Id prefer to leave the extra 1mm bore thickness in the block and get a realible 7-800hp than boring it to 1mm of its life and drastically reducing the blocks rigidity . Have seen a block split at high horsepower with 88mm bore.

1) It's the crank which determines the stroke of the engine.

2) The piston determines the bore size

3) A standard crank has 73.77mm of stroke

4) Running a piston designed for a stroker crank will leave you with a very very low compression ratio as the stroker pistons have a short pin to crown height to accomodate the additional stroke on the crank.

1) It's the crank which determines the stroke of the engine.

2) The piston determines the bore size

3) A standard crank has 73.77mm of stroke

4) Running a piston designed for a stroker crank will leave you with a very very low compression ratio as the stroker pistons have a short pin to crown height to accomodate the additional stroke on the crank.

I've already tried telling him that, but it doesn't seem to be getting through hsugh.gif

My kit isn't the stroker kit, it's the 2.7 ltr kit.  

The stoker kit comes with the crank which I didn't get.

Correct.

It's the crankshaft in the stroker kit that = 75.7mm stroke

You're running standard crank, so you've got a 73.7mm stroke (standard)

I think you might find that it's not just the crank that gives the extra stoke but also the combination of the piston height and conrod length.

The displacement was messured and was found to be just over 2.7ltr.

I'll have to check whether my rods a standard length or not.

Regarding compression, both my head and deck where milled to accomodate the setup the mechanic is seeking.

Correct.

It's the crankshaft in the stroker kit that = 75.7mm stroke

You're running standard crank, so you've got a 73.7mm stroke (standard)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...