Jump to content
SAU Community

Release bearing part number R33GTSTS2?

Torques
 Share

Recommended Posts

Torques Mentor

Torques

Posted
Posted

I'm trying to order the release bearing, the part number seems to be 30502-69F10 (?)

Nengun says it is no longer available.

https://www.nengun.com/oem/nissan/30502-69f10

1997 GTSTS2

Is there a replacement part # ?

Cheers

 

 

 

 

soviet_merlin Mentor

soviet_merlin

Posted
Posted

For what it's worth, Amayama lists some potential replacements:

https://www.amayama.com/en/part/nissan/3050269f10

I don't know whether this is right for you though.

What is your situation?

I have started doing research for a clutch refresh on my car and the release bearing comes with the Nismo kit that I'm looking at.

  • Like 1
BK Grand Master

BK

Posted
Posted
4 hours ago, Torques said:

Hi,

The situation is that I need the standard OEM release bearing for the standard clutch ... :)

Even the genuine one is an NSK bearing - it's not like Nissan make their own bearings.

Torques Mentor

Torques

Posted
  • Author
Posted

Hi,

Yes, thanks for the input.

I'm more than happy to buy from NSK or NTN or SKF.

 

It would help if I had the OEM dimensions but according to SKF I might have found something using

30502-69F10

https://vehicleaftermarket.skf.com/mt/en/products/VKC3737

 

 

 

 

 

BK Grand Master

BK

Posted
Posted
On 19/11/2022 at 3:06 AM, Torques said:

Is there a replacement part #

Most people will be using the Koyo bearing RCT40SA3 from somewhere like CBC here in Australia.

There is a factory Nissan replacement of 30502-69F1A, but it's 100% a Koyo bearing anyway.

Torques Mentor

Torques

Posted
  • Author
Posted

Hello,

Thanks for the input.

 

I also saw the 4075-1S listed as R33GTST  bearing

https://koyo.jtekt.co.jp/en/products/detail/?pno=RCT4075-1S

Here's the 40SA3

https://koyo.jtekt.co.jp/en/products/detail/?pno=RCT40SA3

 

Major difference seems to be 'd' which is 74.5mm vs 82.2mm

Too bad I don't have an old bearing / carrier  to check.

 

 

 

 

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 33GTRV
      Rb26 iron block limit

      By 33GTRV · Posted

      Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
    • GTSBoy
      RB25DET Series 1 & Series 2 Gearbox Identification

      By GTSBoy · Posted

      thumbsup
    • AdiR34
      Did tie rods. Steering now not "springing" back.

      By AdiR34 · Posted

      Appreciate everything guys. I did go ahead and get an alignment... most of my complains are solved. Car is not perfect, but it's good enough. If I notice uneven tire wear or anything I'll just take everything back to stock.  Thanks again!
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      They still have not shipped the 550cc injectors as they weren't in stock, so in theory I could ask to get the 440cc ones instead, if those work better in my scenario. They're the same price so really shouldn't be an issue. Unfortunately I am not so knowledgeable in most parts of tuning so I wasn't sure what's best to choose between the two. 440cc ones are the lowest they have (not in stock, but available to buy nonetheless).
×
×
  • Create New...