Jump to content
SAU Community

Rb20de strange issue not your usual coil pack misfire…

RBZRYUM

By RBZRYUM,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

RBZRYUM Newbie

RBZRYUM

Posted
Posted

Greetings to all you rb cats out there, I’ve run into a slight issue with my rb20de cefiro and am having a fun time trying to diagnose what’s wrong with it 😂 , have read up quite a few forums already posted an I can’t seem to find any close to the issues I’m experiencing.

so basically what’s happening is the car starts takes a few goes when it’s cold yea not ideal but once it fires up it runs relatively smooth firing on all 6, idles pretty good really , once it’s warmed up idles an drives ok  , il give it a good bit of throttle an push it through the rev range an it does so nicely…but as soon as I hit around 6500rpm  it’s farts an shits an sounds like it runs 4 cylinders even once I’ve backed off an just trying to let it idle , the misfires will continue for maybe 30sec to 1minute max then the car will go back to idling smoothly an running on all 6 again. 
 Engine is stock apart from aftermarket coil packs and a Walbro fuel pump.

I have replaced the cas, coil packs, fuel pump , and spark plugs so far.

any ideas would be much appreciated. 

cheers

RBZRYUM Newbie

RBZRYUM

Posted
  • Author
Posted
1 hour ago, Murray_Calavera said:

What type of coil packs are you using now and are they brand new?

Have 2 sets at my disposal an were both relatively new, have checked them over with a multimeter aswell. They are Osaka imports an on set are savage coils

RBZRYUM Newbie

RBZRYUM

Posted
  • Author
Posted
Just now, RBZRYUM said:

Have 2 sets at my disposal an were both relatively new, have checked them over with a multimeter aswell. They are Osaka imports an on set are savage coils

Is it possible the igniter is getting heat soaked an failing?? 

Murray_Calavera Mentor

Murray_Calavera

Posted
Posted
6 minutes ago, RBZRYUM said:

Is it possible the igniter is getting heat soaked an failing?? 

My money is still on faulty coil packs.

If I was in your shoes, I'd throw in a set of brand new coil packs. Either Splitfire or OEM.

 

RBZRYUM Newbie

RBZRYUM

Posted
  • Author
Posted

It’s 100% not coil pack issue , the set has been in a another vehicle that’s been more modified an it ran fine no issues?? Could I maybe have a toast hydraulic lifter??

Murray_Calavera Mentor

Murray_Calavera

Posted
Posted
42 minutes ago, RBZRYUM said:

It’s 100% not coil pack issue , the set has been in a another vehicle that’s been more modified an it ran fine no issues?? Could I maybe have a toast hydraulic lifter??

Any chance you can borrow an ignitor from a running car? 

RBZRYUM Newbie

RBZRYUM

Posted
  • Author
Posted

I have yet to source another igniter an one is relatively hard to find atm, have reached out to the boys but all there igniters seem to have different plug to mine , is there anyway to test my igniter?

GTSBoy Grand Master

GTSBoy

Posted
Posted
25 minutes ago, RBZRYUM said:

is there anyway to test my igniter?

Not really. It's just a box with 6 transistors in it. The usual failure mode is that they refuse to switch the coils when they get too hot, which is probably a solder joint problem, but could be in the silicon. Swaptronics is usually the only way to demonstrate good/bad.

A million years ago I made a set of spacers (out of some ~6mm stainless tube and some longer bolts to lift mine up off the coil cover and try to improve airflow underneath. It did a pretty good job of eliminating the occasional heat soak issue I was having with mine. The ultimate solution was to replace the RB20 with a bigger engine.

If you are having a real problem with the igniter, the correct solution these days is to bin it and the dumb coils and upgrade to a pencil coil kit (R35, Audi, etc). Do the necessary rewiring (trivial) and boost off* into the sunset.

*Sorry, wheeze off asthmatically into the sunset.

RBZRYUM Newbie

RBZRYUM

Posted
  • Author
Posted

Yea I’m currently building a forged 25 for it but love to just drive it around over the summer break , don’t really wana spend money on the 20 haha as you could imagine

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      M35 Aftermarket Fuel Pump

      By MBS206 · Posted

      Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Ben_D
      Wanted to buy R200 longnose LSD 3.9 ratio

      By Ben_D · Posted

      Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Ben_D
      Back for more after 18 years - and where are the longnose R200 LSDs?

      By Ben_D · Posted

      Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • sonicii
      G35 Control arm and Compression Rods into a V35 Skyline.

      By sonicii · Posted

      Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...