Jump to content
SAU Community

RB26 OEM Boost Solenoid Valve terminals

GodziRRa

By GodziRRa,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

GodziRRa Enthusiast

GodziRRa

Posted
Posted

Hi guys,

Just looked at the FSM regarding the RB26’s oem pcm valve/boost solenoid. It says valve terminal 1 and 2, didn’t say wire color etc. I’m no electrician so I’m not really familiar with the symbols. One terminal has a black verical line as some sort of symbol. Anyone can tell which is which? Because I did get a 12v output on a terminal that’s supposed to have none. 😅 Terminal one is for the yellow and blue wire, or that’s the black and red wire? TIA!

21B019B1-0E42-4893-9A85-F3595DC1F403.jpeg

F42E8869-14F2-4221-A424-4C88970F5780.jpeg

8C053BC1-F282-44B6-8D00-8CFB72C11238.jpeg

28400ACA-BFCE-4D1E-9743-DD0A19D56BA7.jpeg

Duncan Grand Master

Duncan

Posted
Posted

They kind of show it in the diagram, terminal 1 is the vertical part of the T and 2 is the horizontal/perpendicular.

But, why do you want to know? That Pin 1 should have power at all times when IGN is on, terminal 2 is pulsed by the ECU to control boost (ground signal)

GodziRRa Enthusiast

GodziRRa

Posted
  • Author
Posted
27 minutes ago, Duncan said:

They kind of show it in the diagram, terminal 1 is the vertical part of the T and 2 is the horizontal/perpendicular.

But, why do you want to know? That Pin 1 should have power at all times when IGN is on, terminal 2 is pulsed by the ECU to control boost (ground signal)

Because I got power at the horizontal terminal with the ignition on not the verical one. 
Just now I started the car, and at idle I’m getting 12v on both terminals. 🤷🏻‍♂️

GTSBoy Grand Master

GTSBoy

Posted
Posted
1 hour ago, GodziRRa said:

Because I got power at the horizontal terminal with the ignition on not the verical one. 
Just now I started the car, and at idle I’m getting 12v on both terminals. 🤷🏻‍♂️

There is no problem here.

Point 1. DC solenoids do not care which way that they are wired up. They throw the solenoid in the same direction regardless of current flow.

Point 2. The solenoid coil is just wire. If you put 12V permanently onto one side of it, and do not earth the other side of it, then the 12V will be measurable at both terminals. That 12V is actually measurable all the way down at the ECU. The ECU doesn't care. When the ECU decides that it wants that solenoid to operate, it provides the earth, by switching on a MOSFET (transistor) inside the ECU that will connect the solenoid terminal to earth (exactly as Duncan^ said). Now the solenoid has 12V being fed in one side and a convenient earth on the other side. Current flows, solenoidy things happen.

  • Like 3
GodziRRa Enthusiast

GodziRRa

Posted
  • Author
Posted
3 hours ago, GTSBoy said:

There is no problem here.

Point 1. DC solenoids do not care which way that they are wired up. They throw the solenoid in the same direction regardless of current flow.

Point 2. The solenoid coil is just wire. If you put 12V permanently onto one side of it, and do not earth the other side of it, then the 12V will be measurable at both terminals. That 12V is actually measurable all the way down at the ECU. The ECU doesn't care. When the ECU decides that it wants that solenoid to operate, it provides the earth, by switching on a MOSFET (transistor) inside the ECU that will connect the solenoid terminal to earth (exactly as Duncan^ said). Now the solenoid has 12V being fed in one side and a convenient earth on the other side. Current flows, solenoidy things happen.

Thanks for that detailed solenoidy reply! Just confused why the supposed terminal that’s giving 12v (ignition on) isn’t giving me any, and the terminal that shouldn’t is giving one. 
If this is the case then we’re problem free. 😊 Some parts of that old FSM still confuses me.

Duncan Grand Master

Duncan

Posted
Posted

But, why were you checking in the first place? The IGN 12v at the boost control solenoid (terminal 1) also feeds a heap of other locations like the PCV, were you trying to sort a problem or just wondering?

The wiring from the ECU to the boost control solenoid is fine for use with a aftermarket ECU and solenoid if required (change the plug at the solenoid end to suit)

GodziRRa Enthusiast

GodziRRa

Posted
  • Author
Posted
17 hours ago, Duncan said:

But, why were you checking in the first place? The IGN 12v at the boost control solenoid (terminal 1) also feeds a heap of other locations like the PCV, were you trying to sort a problem or just wondering?

The wiring from the ECU to the boost control solenoid is fine for use with a aftermarket ECU and solenoid if required (change the plug at the solenoid end to suit)

I just replaced my old krusty solenoid. And since I tested the resistance of the new one, I also tested the wirings because I have a voltmeter in my hand… and I remember before that my mechanic had some rewiring done. 🙂

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • fatz
      Neil's R33 Gts-t Build

      By fatz · Posted

      Have a vb in honour of the car comming back
    • The Bogan
      Neil's R33 Gts-t Build

      By The Bogan · Posted

      It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • perry_r33
      Skyline R33 Sedan Tail Lights S2 - (2 SETS Available) Silver & Grey

      By perry_r33 · Posted

      Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
×
×
  • Create New...