Jump to content
SAU Community

Question about finance

silviaz

By silviaz,
in General Automotive Discussion

 Share

Recommended Posts

silviaz Proficient

silviaz

Posted
Posted

I went to inspect a car and it had finance, now it shows finance from a few years ago and the owner said that it has no finance and he never received an letter or anything. But it shows the registration of the person who had the security interest which isn't the same as the seller's (and that rego doesn't seem to be active anymore), who now has the finance the old owner or the new one? I know usually it follows the owner but it looked odd to me, and shows the finance ends in a few years. 

Link to comment
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

Well that depends on whether the encumbrance is still current or if it's just a zombie. You need to contact the holder of the encumbrance to find out if they actually do still hold it.

These registers are not always going to be 100% accurate. They serve to prevent as many surprises as possible. Here you have a potential surprise. Investigate.

Link to comment
Share on other sites
silviaz Proficient

silviaz

Posted
  • Author
Posted (edited)
6 minutes ago, GTSBoy said:

Well that depends on whether the encumbrance is still current or if it's just a zombie. You need to contact the holder of the encumbrance to find out if they actually do still hold it.

These registers are not always going to be 100% accurate. They serve to prevent as many surprises as possible. Here you have a potential surprise. Investigate.

It's showing this:

Untitled.png

 

I'll give a call to the company next week and if there's no finance get it all in writing. 

Edited by silviaz
Link to comment
Share on other sites
Ben C34 Grand Master

Ben C34

Posted
Posted

I have had the ppsr not clear.

Bought a motorbike off a dude, didn't do the check cos trusted him.

I sell motorbike and guy foes check and itnhas finance!

Go visit guy I bought it off as i remembered where he lived , he was as surprised as me *and surprised to see me* and happy to help ( for perhaps obvious reasons, it was in his interest afterall)

Apparently the bank never updated the register. All fixed and no dramas.

 

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Daleo
      Exemplary Сasual Dating - Real Women

      By Daleo · Posted

      Embrace the freedom of casual encounters on the best dating app in town! Verified Maidens Superlative Сasual Dating
    • dyl33
      Creative in cabin amp locations

      By dyl33 · Posted

      Slimline sub on the rear parcel shelf is doable. Pioneer TS-WX140DA is only 70mm high.   
    • GTSBoy
      Rear suspension upgrades

      By GTSBoy · Posted

      People like Johnny Dose Bro might be laughing at my post because I accidentally added 100mm to my numbers. 350-355 is indeed the lower limit. 450 is off-road Skyline spec.
    • GTSBoy
      Pillowball/Hardened Runner Hybrid Approach

      By GTSBoy · Posted

      What is the "compromise" that you think will happen? Are you thinking that something will get damaged? The only things you have to be concerned about with spherical jointed suspension arms are; Arguments with the constabulary wrt their legality (they are likely to be illegal for road use without an engineering certificatation, and that may not be possible to obtain). A lot more NVH transmitted through to the passengers (which is hardly a concern for those with a preference for good handling, anyway). Greatly increased inspection and maintenance requirements (see above points, both).   It is extremely necessary to ask what car you are talking about. Your discussion on strut tops, for example, would be completely wrong for an R chassis, but be correct for an S chassis. R32s have specific problems that R33/4 do not have. Etc. I have hardened rubber bushes on upper rear control arms and traction rods. Adjustable length so as to be able to set both camber and bump steer. You cannot contemplate doing just the control arms and not the traction arms. And whatever bushing you have in one you should have in the other so that they have similar characteristics. Otherwise you can get increased oddness of behaviour as one bushing flexes and the other doesn't, changing the alignment between them. I have stock lower rear arms with urethane bushes. I may make changes here, these are are driven by the R32's geometry problems, so I won't discuss them here unless it proves necessary. I have spherical joints in the front caster rods. I have experienced absolutely no negatives and only positives from doing so. They are massively better than any other option. I have sphericals in the FUCAs, but this is driven largely by the (again) R32 specific problems with the motion of those arms. I just have to deal with the increased maintenance required. Given how much better the front end behaves with the sphericals in there.....I'd probably be tempted to go away from my preference (which is not to have sphericals on a road car, for 2 of the 3 reasons in the bulleted list above), just to gain those improvements. And so my preference for not using sphericals (in general) on a road car should be obvious. I use them judiciously, though, as required to solve particular problems.
    • joshuaho96
      Misfire/stalling issues

      By joshuaho96 · Posted

      Easiest way to know is to break out the multimeter and measure it when cold, then measure all the resistances again once it gets hot enough to misfire. Both the original ignitor and the J Replace version. Factory service manual will have the spec for the terminal measurements.
×
×
  • Create New...