Jump to content
SAU Community

Recommended Posts

Hi all, trying to get my AWD system working properly after a soup to nuts rebuild. The computer is throwing codes 8, 9 (ABS was deleted) and also code 18 which seems to be the issue. Today we tried the bleed procedure and still doesn’t work.
 

Here’s the description from the builder: on ignition the pump pumps oil, when the pressure reaches the desired value, the pump turns off and the oil is stored in the tank by closing the check valve, in our case it seems to me that it does not work and when the pump pumps up the pressure to the operating level , the sensor turns it off and the liquid is squeezed back through the pump into the tank, you can even hear the pump spinning in the opposite direction, the pressure decreases and the sensor turns on the pump again, and this all repeats endlessly.

The AWD system worked after I bought the car but not since the rebuild. I changed the G sensor to the Do-Luck unit, maybe that could also be the issue? It’s a pain to change so we haven’t tried it yet

 

Hopeful to get this worked out, I really wanted an AWD skyline. Thanks 🙏 

Link to comment
https://www.sau.com.au/forums/topic/485106-attesa-code-18-pump-malfunctioning/
Share on other sites

Probably worth starting with the 32 GTR workshop manual (you didn't say which car and don't have it on your profile).

https://www.hgeconsulting.com.au/gtr_32_service_manual_indexed.pdf section c3 stars page CH-57

My mistake yes it’s a 32 GTR, I’ll check it out but we did find the code 18 troubleshooting and all the referenced points have continuity, so the flow chart says the computer is faulty. Just seeing if anyone had a similar issue before shotgunning parts. Thanks

Yeah that does suck considering how hard these computers might be to find, wherever you are.

80s Electronics were mind blowing to the 80s, but not so much these days. Might be worth opening the computer and looking for any burned tracks or components or other obvious issues rather than replacing it straight up

I think it’s possible a defective part on the hydraulic pump like the pressure switch is causing the fault, I checked the troubleshooting flow chart again and it actually says hydraulic unit failure, so I guess that’s the pump, but my pump is cycling constantly so my thinking is either a valve was installed wrong or a part is not working properly

Or the do-luck G sensor is defective?

Issue inside the hydraulic unit was my thought after looking at the guide too, but I haven't really heard of that before. Potentially it is just the pressure switch has failed, original is not available but there are aftermarket equivalents like this from Frenchys https://frenchysperformancegarage.com/products/fpg-nissan-gt-r-attessa-pressure-switch-replacement

I can't see how the g sensor would cause the issue but it is easy to check, just unplug it. The hydraulic unit should pressure up regardless of what the ECU thinks is happening in the car

 

On 11/25/2023 at 3:12 PM, weikleenget said:

I think it’s possible a defective part on the hydraulic pump like the pressure switch is causing the fault, I checked the troubleshooting flow chart again and it actually says hydraulic unit failure, so I guess that’s the pump, but my pump is cycling constantly so my thinking is either a valve was installed wrong or a part is not working properly

Or the do-luck G sensor is defective?

G sensors do not affect the pump. Entirely separate issues. Most likely your hydraulic unit has some fault. Is your nitrogen accumulator reasonably new? If it’s original you probably need to replace it along with whatever else is broken. 

8 hours ago, joshuaho96 said:

G sensors do not affect the pump. Entirely separate issues. Most likely your hydraulic unit has some fault. Is your nitrogen accumulator reasonably new? If it’s original you probably need to replace it along with whatever else is broken. 

Yes the accumulator was changed new, I’ll try change the pressure switch and see if it clears the fault

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...