Jump to content
SAU Community

Recommended Posts

Hello.

my R32 is ready to start but I received a message which has thrown a small spanner in the works. I currently have everything built to hold 1600hp. Engine (3.2L), fuel system, sequential drive train. However the Turbo is a gen 2 7685 T4 1.12 rear (1350hp). I have an offer of doing a straight swap for a gen 2 8685 with the same rear housing (1500hp). this will put the turbo in line with the rest of the setup regarding HP potential. 

main purpose of the car is drag and roll racing. I will be driving it on the street as often as I can. If anyone has any real work experience with a turbo that size, what’s it like on the street. Would love some dyno graphs. I would even welcome opinions. I found a few dyno graphs of these turbos on 2JZ engines which is a reasonable comparison but there is no rpm reference on the graph. It’s all MPH based. 
 

thanks to everyone in advance. 

Link to comment
https://www.sau.com.au/forums/topic/485218-from-7685-to-8685/
Share on other sites

Which sequential? Do you know the ratios? Assuming your first will be super long as well, making it seem more laggy. Plus you're going to be running a massive turbo, and its a precision, so will be laggy as hell on the streets. Expect to be gapped by prius's. Precisions dont do compressor maps which kinda sucks.

What work have you done to your head? Please make sure your engine builder degree's your cams!! We just played with the cams on mine and its alot more responsive and made a wee bit more power.

Thank you for the reply.

Head has the works done to it. Port polish, oversized valves. Biggish cams. I will spend as much time as needed on the dyno getting this thing right  

the only real wold result I’ve seen is WARGTR dyno where he made 1410hp but the line was a perfect slope. 
 

I realise a 6466 will be a street weapon but that’s not really the purpose of the car. I guess I’m still remembering old bush bearing Japanese turbos with dyno graphs like Mount Everest  

I won’t be racing people on the street (much). Occasional hwy push or a scare of a passenger on a cruise maybe. Planning lots of track time. Just don’t want the turbo to completely choke the engine. From what I see with all the US supra videos, doesn’t seem to be the case. 

Great video. Thank you.
 

I actually got a few messages back from guys that use 8685. So far 100% thumbs up. Almost all of them went from a 7675 or a 7685. sentiments were along the lines of “once your balls grow big enough, you’ll win lots of races”. All said that it is still very drivable on the street. Being a 3.2 with 9-1 comp ratio. Sequential box. Light tail shaft. It will spool nice and even. Will have all of the power in the 5500-8500 range where you shift. 

This was a free upgrade. Well just the cost of postage. Going 8085 meant forking out thousands of dollars and having an extra turbo in the shed hoping it sells.
 

next Gen is still very new and there is not allot of comparison data to Gen 2. I haven’t seen any videos where new 8085 clearly beats the old 8685 for outright HP. Even though it is meant make 100hp more. A couple of people I have spoken to that have gone next gen say it makes similar power but does make it a little earlier in the rev range. Best example is RHM R34 gtr. Romanos does a back to back run with that exact combo. He makes the same power and he would max out both turbos for sure. All he said is he gained some torque. Not allot, just some. And went Pro Mod immediately after. I am not in the racing catagory where 500-1000rpm will make a difference to my results. I’m sure my GTR with an 8685 will make me shit my self for years to come. By the time I say “I need more power” there will be something better out anyways and I will be going billet block and getting divorced. 

1 hour ago, khezz said:

Not allot, just some. And went Pro Mod immediately after. I am not in the racing catagory where 500-1000rpm will make a difference to my results. I’m sure my GTR with an 8685 will make me shit my self for years to come. By the time I say “I need more power” there will be something better out anyways and I will be going billet block and getting divorced. 

I was reading through the post and the comments and was basically going to say something along these lines - feels like you answered your own question really ;)

I haven't had direct experience with the exact kind of setup you are talking about here, but my observations and involvement with things of this level basically surmounts to - once you are talking about 80mm+ turbos on "small" engines the lag etc all becomes a bit academic.   You are going to NEED launch/rolling start antilag, you're going to need to rev the hell out of it and a fast shifting trans with shift cuts are ideal if you want to keep progress happening well.

At this point if you want more power and you have an option, the only thing to think hard about is "Do I have the trans, fuel system, and engine spec to ensure I can use the upper end of this turbo?".  If you don't, then probably a waste of time... the extra lag without being able to get the treats is pointless.  If you can use pretty much all it has to give, may as well.   

Edited by Lithium
  • Like 1

I was wondering when you would through some wisdom in. 
 

everything is built to withstand 1500-1600hp. Turbo was the only part that was slightly shy. If you can call 1350hp shy. 
 

Car will be driven often on the street. Can call it a daily but it’s not a street racer. If it was I would have gone 64xx or 68xx. This is mainly to go low 8s on the quarter and win roll racing. Sequential with FBW/flat shift. Two step, light tail shaft, front and rear drag spec diffs. 
 

I was hoping for some seat of the pants experience. Anthony (WARGTR) and Romanos (RHM) were very forthcoming coming. Both said that there is very little difference between 76 and 86. On the street you change under 4K anyways so it’s a nice quiet street car. The 3.2 with its counter weighted crank revs very well and has enough capacity for town driving. If you do decide to do a squirt, you would shift down and from 4500 onwards there is nothing that can keep up with you. 

14 minutes ago, khezz said:

I was hoping for some seat of the pants experience. Anthony (WARGTR) and Romanos (RHM) were very forthcoming coming. Both said that there is very little difference between 76 and 86. On the street you change under 4K anyways so it’s a nice quiet street car. The 3.2 with its counter weighted crank revs very well and has enough capacity for town driving. If you do decide to do a squirt, you would shift down and from 4500 onwards there is nothing that can keep up with you. 

Yeah makes sense to a degree, like you have a "strong" 3.2litre engine anyway.  As soon as it starts getting any boost the displacement advantage gets compounded and you start picking up speed (and with that, rpm) quicker than the poor beggers with 2.6s and even 2.8s.

As soon as you get it up and cooking its going to be insane, but its only going to be useful in races you're allow to get up on launch control or at least involve very illegal speeds on the road but you were already there with the 76mm. 

  • Like 1

I’d like to hear this sad tale please…

38 minutes ago, r32-25t said:

I’ve said a few times if I was starting again I’d go 3.2, but I had the stoker kit before I knew about the block being stuffed 

 

1 hour ago, khezz said:

I’d like to hear this sad tale please…

 

Basically slowly kept modifying a standard engine and ended up with a 6466 on it and then ended up with coolant spraying out of the over flow bottle on boost, thought it had just lifted the head and was going to throw a 2.8 kit into the factory block and keep going.
 

Got the head off and found the block was cracked in 4 spots (3 in the deck and one in the side) and because I already had the 2.8 kit I bought a billet block for that to go into. 

I went up to a 6870 im hoping I won’t regret it

the machine shop/engine builder has it at the moment, I don’t know the exact details of what happened apart from water was getting into the oil and after they did a pressure test it was coming from behind a sleeve 

 

Couple of comments:

The 8685 is laggy. You will definitely feel the difference between a 7685. 

With a manual don't expect anything to really happen before 6,000rpm. You'll probably need to rev to 9,000 to get the most out of the 8685.

I've had friends with 8685 and a Samsonos, 3.2 and it is still laggy/doughy.

I've had both 8685 and the 8085 and there is certainly a noticeable difference between the two. The 8085 does make slightly more power but my convertor doesn't want to show it....

If it's roll racing then you will need to ride the fk out the clutch to get it on. Make sure you have something that will cop the punishment otherwise you'll get left behind. The direct clutches 9 inch what everyone in Sydney is using and that is taking the punishment. Everyone in Sydney is now using gas to help get out of the hole too. You might need nos.

I don't know how long the track is at Perth but you'd want to be comfortable that you have enough track to really use the hp from the 8685.

If your main focus is drags and RR where the extra power can be used the go the 8685. There is no chance of putting down 1500hp on the street (not to mention that it is dumb!).

If you want an all rounder then you may wish to rethink the 7685.

 

  • Like 2

Wow. You are the first to give the 8685 a thumbs down (of sorts). I am using an OS quad plate clutch. I would rather stay away from gas if I can. Personal preference really. Sydney RR is probably the most competitive in the world. I have never been but by all the videos and written accounts, if you aren’t pushing 1500+ hp, you aren’t even fighting for a podium. That’s insane for such a young competition. With Perth, 1000hp puts you close towards the top. We have a nasty turn at the end of our straight. Scary as hell. 
 

on the street, I will be using 98 octane and keeping the boost down. I’m thinking 700-800hp no more. Anything above that is not really usable. Most of my street duties will see the engine in the 2500-5000 rev range. Drags and RR is the main purpose of the car. Maybe a dyno comp from time to time. 
 

cheers for the info. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...