Jump to content
SAU Community

Recommended Posts

Morning :)

little intro to the build r32 rb25 with a gtx3582 haltech platinum pro, 1000cc injectors 460 walbro fuel pump “maybe larger” with new lines and relay setup, new fuel lines an a FPR 1200. Made 350kw and Have had the car back now for a couple weeks haven’t had any real issue but this Sunday I got my first issue…. I generally fill up E85 at astron yagoona and with a quarter tank and on the way to a cars and coffee I stopped off at minto and put a full tank in it. 

after about 10 mins of driving and letting it all settle in the car started to misfire and splutter? nothing consistent but noticeable? on the way back spent about an hour on the free way at 110km/h cruising at about 3000rpm and this is where the car started to splutter intermittently and wouldn’t give me any boost if I dropped to 3rd gear would stop and let me have boost then start again when I would consistently cruise at 3000rpm this is where progressively the splutter would get more consistent. 
 

im about to check the fuel but the e85 at minto has always been consistent, I have aftermarket r35 coils and have pulled them apart and they look good to go and injectors sound to be doing there job? 

At idle I don’t have any issues when i let it idle for a while and gave it a few solid revs and nothing? When I got off the motor way and was driving city speeds/ traffic “50km/h” no splutter?
 

Could it be a:

fuel issue?

coil issue?

tune issue?

will go for another drive to see if it starts up again and see.

 

any helps appreciated!!!!

 

Edited by 32pwwr
Link to comment
https://www.sau.com.au/forums/topic/485732-rb25-splutter/
Share on other sites

3 hours ago, Murray_Calavera said:

Can you go for a drive, log all the channels and post the data up?

That would be too easy for diagnosing. It's more fun to play throwing darts aimlessly...

 

I vote change the O2 sensor. Reason? None, just a random dart thrown.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/485732-rb25-splutter/#findComment-7992133
Share on other sites

16 hours ago, MBS206 said:

That would be too easy for diagnosing. It's more fun to play throwing darts aimlessly...

 

I vote change the O2 sensor. Reason? None, just a random dart thrown.

Love it haha, tuner came around and checked he said the timing was out and finds the Ross trigger kits to be a bit touch and go… back to his shop Thursday to fully diagnose but he thinks timing is the cause as we checked fuel pump, fuel filter, injectors, ignition and all came back good…. 
 

was very weird tho as only happened under sustained load cruising on the m7 at a sustained rpm and speed it would start sputtering felt like anti lag as when I put my foot down it would sputter or break up and not give me any boost then pull like a freight train when it gave me boost and was all at once

Edited by 32pwwr
Link to comment
https://www.sau.com.au/forums/topic/485732-rb25-splutter/#findComment-7992144
Share on other sites

I would be suss that that behaviour was caused by the trigger kit. The trigger kit doesn't really care what the engine load is. It's just seeing moving metal next to sensors. It may fail to work at a particular engine speed, but wouldn't care if it was low load, medium load or high load. And it probably shouldn't change moment to moment. It's either good or bad, unless it is temperature dependent.

The symptoms you describe are typically fuel or spark delivery related.

Link to comment
https://www.sau.com.au/forums/topic/485732-rb25-splutter/#findComment-7992145
Share on other sites

9 minutes ago, GTSBoy said:

I would be suss that that behaviour was caused by the trigger kit. The trigger kit doesn't really care what the engine load is. It's just seeing moving metal next to sensors. It may fail to work at a particular engine speed, but wouldn't care if it was low load, medium load or high load. And it probably shouldn't change moment to moment. It's either good or bad, unless it is temperature dependent.

The symptoms you describe are typically fuel or spark delivery related.

That’s what I was thinking, builds all under warranty so hopefully they figure it out quickly and I can post what the issue is

Link to comment
https://www.sau.com.au/forums/topic/485732-rb25-splutter/#findComment-7992147
Share on other sites

12 minutes ago, GTSBoy said:

I would be suss that that behaviour was caused by the trigger kit. The trigger kit doesn't really care what the engine load is. It's just seeing moving metal next to sensors. It may fail to work at a particular engine speed, but wouldn't care if it was low load, medium load or high load. And it probably shouldn't change moment to moment. It's either good or bad, unless it is temperature dependent.

The symptoms you describe are typically fuel or spark delivery related.

I also would like to note that the r35 coils packs are aftermarket… and did note to him I feel that they are possibly breaking up under sustained load and heat as when I got home and let it idle had no issues and when I got off the freeway and started driving city speeds had no issues, so going to purchase hitachis.

first time really driving it for so long aswell as I’ve only had it for 1-2 weeks. 

Edited by 32pwwr
Link to comment
https://www.sau.com.au/forums/topic/485732-rb25-splutter/#findComment-7992148
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...