Jump to content
SAU Community

Recommended Posts

is it only the right mirror that needs to be replaced troy?

intrusion bars i will get my bro in law to do... so thats not too much of an issue but where do u actually get them from??

Link to comment
https://www.sau.com.au/forums/topic/49465-the-beast/page/3/#findComment-989185
Share on other sites

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

oh when i make them i use 70x25mm box section and make it in 2 sections so you can get it in the door....then i join the two peices up by using 3 peices of 20x20 stacked on top of each other and i make those slide into each peice by about half the length of each 70x25 box section(telescopic)....then i weld it all up in place and by the time youve welded them it takes up the 7mm diffrence in the 3 peices of 20x20(20x3 =60...inside of main intrusion bar is around 67mm)make any sense?Why dont you do them yourself?You say you are a panel beater by trade,shouldnt be too hard for you......As it is your safety thats is at stake,and its usually only the rh glass that needs to be done...you could change the other side if you want to be anal and keep them both the same

Link to comment
https://www.sau.com.au/forums/topic/49465-the-beast/page/3/#findComment-989322
Share on other sites

ni you must be stoked!!! My car made it to Sydney a couple of weeks ago, apparently waiting for parts for compliance?? It's been that long that it doesn't really feel like i've bought a car anymore, it's just this thing that i have to keep trying to move forward. It must feel great to finally get to drive the beast!

AND SHAN REPLY TO MY EMAILS/PM'S/MSN MESSAGES YOU LAZY BASTARD :P i need to bout this Masa kit...

what was the reason for your hold up ni? I had a 2 import approvals go missing.... :)

Link to comment
https://www.sau.com.au/forums/topic/49465-the-beast/page/3/#findComment-989366
Share on other sites

oh when i make them i use 70x25mm box section and make it in 2 sections so you can get it in the door....then i join the two peices up by using 3 peices of 20x20 stacked on top of each other and i make those slide into each peice by about half the length of each 70x25 box section(telescopic)....then i weld it all up in place and by the time youve welded them it takes up the 7mm diffrence in the 3 peices of 20x20(20x3 =60...inside of main intrusion bar is around 67mm)make any sense?Why dont you do them yourself?You say you are a panel beater by trade,shouldnt be too hard for you......As it is your safety thats is at stake,and its usually only the rh glass that needs to be done...you could change the other side if you want to be anal and keep them both the same

sweet as thanks troy... my bro in law has the welder so i'll just get him to do it for me... hes a lot better with the welder than i am.

thanks for the instructions mate.

Link to comment
https://www.sau.com.au/forums/topic/49465-the-beast/page/3/#findComment-989662
Share on other sites

ni you must be stoked!!! My car made it to Sydney a couple of weeks ago, apparently waiting for parts for compliance?? It's been that long that it doesn't really feel like i've bought a car anymore, it's just this thing that i have to keep trying to move forward. It must feel great to finally get to drive the beast!

AND SHAN REPLY TO MY EMAILS/PM'S/MSN MESSAGES YOU LAZY BASTARD :P i need to bout this Masa kit...

what was the reason for your hold up ni? I had a 2 import approvals go missing.... :)

hehehe yeah very happy its finally here... makes it all seem worth it :)

the main hold up was myself getting the money together in time... other than that everything else went pretty smoothly.

Link to comment
https://www.sau.com.au/forums/topic/49465-the-beast/page/3/#findComment-989674
Share on other sites

nark come past my work i'll fix ya a mirror for ya :)

 

and yeah, it is only the right one that needs to be flat

hehehe cool... once i get a UVP for it i'll drive over ur side of town :P

Link to comment
https://www.sau.com.au/forums/topic/49465-the-beast/page/3/#findComment-989675
Share on other sites

what's a UVP? oh wait... Unregistered Vehicle Permit??? Do you have details on that because my car might be down here in Melbourne before it can be regoed as well...

cheers.

oh and if you see or talk to Shan, tell him to reply to my various msg's!!! :)

Link to comment
https://www.sau.com.au/forums/topic/49465-the-beast/page/3/#findComment-989682
Share on other sites

lol chinny... yeah thats what it is... u have to ring vic roads to get em... u can either pick em up or have it faxed thru... cant remember the costs involved... depends on how long u want it for.

Link to comment
https://www.sau.com.au/forums/topic/49465-the-beast/page/3/#findComment-989738
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...