Jump to content
SAU Community

Recommended Posts

I tried the swap on sunday unseccesfully....

Changed them without any problems, checked everything was the right way, i even had a copy of the GTR manual to guide me thru.

But when it came to starting it would start up and idle very bad.

It was very lumpy and it wouldn hold idle at all. I played with the PFC ign/inj adjustments, but it didnt make much difference.

At one stage it stayed idling but it was very rough. I also noticed that the boost gauge was only showing very little vacuum about -5mmHg.

After alot of frustration we started thinking it could be the valves are already opening as the RB26 cams are 0.1mm thicker than the RB20s at the lobe. Which in turn will push the the valves 0.05mm open.

I still dont really understand the hydraulic lifters concept and how they work. As i understand it when the lobe is pushing down the lifter it is solid as the oil cant escape and when it comes up it fills up with oil untill it gets pushed down again.

So i suspect what might be hapenning is that putting the RB26 cams straight in without taking the oil out of the lifters will make solid and thus opening the valves, and then never fully closing as the oil cannot escape fully.

If thats correct that would mean that before putting the RB26 cams in one should empty the oil out of the lifters.

Im not sure if thats right, but if someone can clarify the lifter operation that would be great.

RB20 cams are back in and everything is fine again....

Link to comment
https://www.sau.com.au/forums/topic/50069-rb26-cams-in-rb20-didnt-work/
Share on other sites

  • Replies 100
  • Created
  • Last Reply

Top Posters In This Topic

Sorry to hear it didnt work!

you have had the exact same problem as 4 of us who have tried it. has anyone here bolted in some HKS or Tomie items into their RB20 yet? i dont understand why they should work as a bolt in, yet the GTR ones cause so many problems...

After alot of frustration we started thinking it could be the valves are already opening as the RB26 cams are 0.1mm thicker than the RB20s at the lobe. Which in turn will push the the valves 0.05mm open.

How did you come to measure / identify they are 0.1mm thicker? What / where is that a measure of?

They work for me. i made sure to soak the lifters in oil for a few hours before i installed them.

are u guys sure that you don't have any vaccum leaks, as i have just rebuilt my engine all hoses with new hose clamps and all, the went to tune it and it wouldn't idle. ended up being that nearly all the hoses on the intake manifold where leaking. (yes they were tight)

Roy: It is measured at the heel of the lobe the flat section with no lift.

Ahh32: Why did you soak them in oil??

WazR32GTST: Can you confirm that your mechanic actually bled them before he put them in?

Im still not convinced thats the reason why they havent worked. Maybe Sydneykid can help here ...

i can confirm that my mechanic bled them

when i picked the car up he said to me that he bled the lifters. not sure if he did it because they were noisy with the old cams or that this is a standard protocol for a cam change. either way i am 100% positive that this was done.

Waz.

I dont' want to sound like a spoil sport - but whoever put GTR cams in their car and had it idle didn't use GTR cams. You got ripped.

The reason that GTR cams don't work without going into too much detail is that mechanical cams (all GTR and R34 GTT) have a linear lift ramp which in a GTR is app. 0.55mm high and takes something like 50 degrees to reach that point. In a mechanical cammed motor the clearance should be set at the point where the ramps meet the cam lift. (at hot running) So in a GTR, the tappets should be set at about 0.5mm, but Nissan recommend a smaller clearance which not only makes the car sound tough as (as GTRs do) but allows for a lot of valve growth (which GTRs do).

IF you run the GTR cams in a hydraulic cammed motor, you end up with cams that have about 360 degree duration on the seat instead of about 240! This is utter stupidity and should not be done. I am not taking a slash at the people who have done it, but at the people who say it is good and can be done. If it does not make complete sense to you, don't worry it takes a while to get your head around, and I can draw you a picture one day if you want.

Luke

Sorry I phrased it wrong. GTRs have a lot of valve growth and this is characterised by their larger than normal ramp sizes. Honestly I think they specify their clearances to be so tight purely to make the GTRS sound tough. And man does it work! If you run the 'right' clearance in the GTRs it would sound a lot more sedate on idle and low speed running but still make the same HP.

hmmmm dunno bout that.....your meant to run them as tight as you can get them....well this is the case in motorcycle racing,but they get pulled apart every race so i guess that wouldnt work in an everyday situation....i have also noticed that the inlet valve has a larger clearance than the exhaust(which is opposite to the way it normally works)one would assume that this would be due to the sodium filled exhaust valves that RB26s have....

i have never seen Nissan clearances. I know what they are meant to be because I have cam doctored GTR camshafts, plotted them and found out what clearances are needed to run them at. Noramlly you put 0.05mm more clearacne on the exhaust to accomodate growth. Anything half decent runs Inkinel (spelling) or sodium filled exhaust valves. At the end of the day who gives a toss? GTRs have big ramps and need larger than expected lash settings. Nissan set them closer than they need to be. I bet they didn't set them at this setting for emissions testing but...

If you are a hard core racer, you set the tappets wider than usual and you eat valve springs, but thats the price you pay for HP.

Do not run Solid camshafts in your hydraulic car. Its not fair to people like jnr32r who take your word and end up wasting their time and money trying it. Try to keep the BS to a minimum and this will be a nicer place.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...