Jump to content
SAU Community

Recommended Posts

still have a miss in my r33 under load at 5000rpm at 10psi.

have changed the spark plugs.

had it on the dyno with a fuel pressure guage( pressure good flow low)

replaced the fuel pump(nippon denso high pressure 400hp pump)

im going to clean the coil contacts where they go onto the spark plugs and ill check the little springs in the end of the coils.

want to know if anyones heard of boost cuts being as low as 10psi?

or maybe a boost sensor on the motor thinking it is over boosting?

the knock sensor might be sensing pinging at this certain rev? (havent heard any pinging)

any ideas let me know.

Link to comment
https://www.sau.com.au/forums/topic/50073-same-problem/
Share on other sites

when u changed ur plugs did u set a correct gap? .8mm is the general consensus here. what plug heat range did u use?

also do you have aftermarket ecu? stock ecu will sense boost increase and kicks in boost cut, can be as low as 10psi especially on cold nights. pfc will definitely fix that, otherwise a cheaper safc can do the job well if tuned properly.

Link to comment
https://www.sau.com.au/forums/topic/50073-same-problem/#findComment-996382
Share on other sites

hm.. hard to tell. cutting boost wire may not bring u anywhere as the ecu will need afm input, otherwise it'll go to limp-home mode and stutters at 2000rpm (found out abt this when my one of my afm wire was accidentally snagged).

i think could be something else causing it to miss. hopefully not a serious issue. can be quite a bitch to track down. i had similar issue in my car for over a year when it turned out to be fuel pump dying. had it replaced and all is sweet.

oh i just remember, what boost controller u use to run 10psi? dun trust any simple cheap bleed valve, it may spike, especially on higher gear. ask ur tuner to check it on dyno. best boost controller are always the electronic ones.

Link to comment
https://www.sau.com.au/forums/topic/50073-same-problem/#findComment-996443
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I havent bought a manual cover for the dash yet and no cluster change, won't bother me too much, I just need to get that auto box gone, manual in! I miss my manual. 🤪. We started last weekend and managed to get the box out. Planning to start putting it in this weekend and then order a single piece tail. We were super careful to take time and not damage anything. It's my first time working under the car.  With my S15 mainly worked in the bay. This time, it was a headache because of three or four bolts only. They simply didnt want to leave thei homr and the one securing the tailshaft, another above the GB, and the one securing the lipstick was a shit. Mates mate, Davo caught fire 🤣, nearly opened his chest up with a grinder 🤦🏽‍♂️ and both mates nearly had a plate from the box land and slit their head open. Fun times. We all survived. Not the easiest working with limited access on jackstands. As I'm sure we can agree these are the memories which make us love our car. For all three of us, was an awesome weekend and Sunday 3.30am before tools down was a fantastic effort. I need to upload pics, but looks like it needs to be via Url now. We used to be able to just upload pics back in the day. It's been that long! 🤪 Im currently spraying rustoleum under body, not because it's rusted. It's super clean, but just so it's protected for the next 10 years. There was a few surface rust spots. Which pretty much wiped off with a 3M scourer.  Really impressed with how well the previous owner maintained it. Bank account went down so quick! Service, then GB - managed to get a spanking new 34 genuine box from Nissan. All the rest of the conversion parts from Kudos.  Went with a Nismo short shifter. New pedals and Exedy Clutch and FW. Ordered the Prp Rear Main Retainer kit which should arrive Friday and my first engine mod part just like I did with my S15 will be the Tomei Expreme Turbo Outlet. Already on order. It'll likely sleep next to me on a pillow during the coming months. 🥰 Last build was on my JET200GT profile and on SAU and Hardtuned I had documented the build. Planning to try to do that again. Brands feel scarce now. Wish we still had ARC and Apexi parts readily available. Exhaust - need some advice on this. I had an Apexi exhaust on the S15 and loved the tone. My mate had a HKS HP Silent on his 33 and suggested I go with that to avoid drone. I can't remember hearing an RB25DET running that so will likely need to wait for a meet or something to hear it.  Not after big power, just enjoy building it, and drivability with minimal negative attention.
    • Have a chat with Ben at Moore Performance or Jesse at JS Performance.
    • Thanks both. All good advice. Reminds me of drilling through stone wall for drainage pipe 😬 I'll let you know how I get on if I still have use of my hands afterwards 😅
    • Finally got shipping number for the intake and throttle body, shipped by UPS, so "should" be in my hands sometime next week, fingers fracking crossed
    • I'm so far behind in the jobs I have to do at both work and home (including car) that I have become immortal. There's simply no way that I can die now.
×
×
  • Create New...