Jump to content
SAU Community

What's wrong with my brakes...

Remix-

By Remix-,
in General Automotive Discussion

 Share

Recommended Posts

Remix- Mentor

Remix-

Posted
Posted

After a few hard brakes and some spirited driving in the gtst, i was cruising down a street and went to hit the brakes and there was nothing there!! The pedal went all the way to the floor, i pumped them then it sort of came back then there was nothing. I left the car at home then the next day went for a drive and everything is perfect again? Though i am feeling very uneasy about braking atm after what happened. Any ideas would be greatly appreciated!

Some of my thoughts:

Brake master cylinder is on the way out?

Brake fluid is crap?

Brakes need to be bled?

Link to comment
https://www.sau.com.au/forums/topic/51141-whats-wrong-with-my-brakes/
Share on other sites
Jae_s15 Rookie

Jae_s15

Posted
Posted

I would guess that you more than likely need the brakes bled and get new fluid. Sounds like you current brake fluid has absorbed a fair bit of water and is boiling really easily, as the spongy pedal is the main symptom of overheating fluid. Don't know what you currently use, but it might be worth upgrading to something like a DOT 5.1 fluid or something along those lines.

If that doesn't fix it, then have a better look at other possible problems.

Cheers,

Jae.

slipperywhenboosting Contributor

slipperywhenboosting

Posted
Posted

If you have cheap brake pads on it and you were driving hard you may have heated the pads up past their working temperature causing them to lose there resistance which would explain why they worked fine afterwards,(they cooled down) this happens a lot when the pads are low aswell, i dont think it would be the master cyclinder, check for leaks anywhere on the brake line or the master cylinder though.

benm Grand Master

benm

Posted
Posted
Thanks mate, i will bleed the brakes the following weekend and change the fluid.
My suggestion would be to take it to the best brake mechanic in your area and explain what happened. You are best off getting new brake fluid (which involves getting them bled). I spent ~9mths with a very bad brake pedal and driving was no fun. It cost well over $2,500 in total, I got everything fixed/upgraded because the feeling of having no brakes is the worst and I was happy to spend money to ensure it doesn't happen again.

Once your fluid has boiled, replace it.

I boiled/cooked my brakes so badly after literally 2x 10 lap sessions (very average speed laps too) at Eastern Creek that it destroyed my brake system. Pedal went to the floor, pumping it did nothing, had to limp home and it basically spent the next week at a workshop and took more than 5 mechanics and ~9mths of mucking around to get the problem solved.

Good quality DOT5.1 will cost about $100 and an hour of their time. Depending on how much damage you have done you may also require new brake pads which could be around $200 all up.

It's fun hitting boost and watching that speedo increase rapidly, it's not fun watching the car infront get closer and closer with your foot already firmly on the pedal.

riggaP Veteran

riggaP

Posted
Posted

Sounds like you cooked the brakes. Better pads and fluid should fix it.

The same thing happened in my previous car, which was caused by a faulty handbrake. The master cylinder followed soon after :) It had a similar feeling under the pedal but a lot more expensive to fix.

SLIM V 2.1.0 Enthusiast

SLIM V 2.1.0

Posted
Posted
After a few hard brakes and some spirited driving in the gtst, i was cruising down a street and went to hit the brakes and there was nothing there!! The pedal went all the way to the floor, i pumped them then it sort of came back then there was nothing. I left the car at home then the next day went for a drive and everything is perfect again? Though i am feeling very uneasy about braking atm after what happened. Any ideas would be greatly appreciated!

Some of my thoughts:

Brake master cylinder is on the way out?

Brake fluid is crap?

Brakes need to be bled?

I reckon you should take another driving test?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...