Jump to content
SAU Community

Recommended Posts

i thought there was a section on businesses but it may have been in another site. oh well, i will tell the story.

i was looking for an import when someone pointed me in the direction of yahoomotorsports. i went on the net and looked at the cars and found one that i wanted, called for the details, words were something like, "it is fairly straight and clean, its a pretty good one". wanted half deposit to ensure i wasn't screwing him around which was able to be refunded but $100 when it arrived if i didn't want it. I knew the risk i was taking so that was ok. The car arrived and went to see it, the body looked ok, panels anyway. But it was still a dodgy car on closer inspection, he said test drive it. i didn't even get over 20km/hr and i knew their was a problem! then when i went to stop the car metal on metal brakes, don't we love that noise, which meant disks had to be replaced (more money). Didn't know what the problem is though, loud clunking noise and loss of power, sounded like it spun a bearing but it went away on low revs. i asked can you get it checked out with a response of a chuckel and "It's not my job" and a consistent, "do you want it or not, yes or no?". well i wasnt risking having to spend thousands if there was something seriously wrong with it and then trying to get it through regency! so he held his word and refunded the deposit minus the $100. i later got a reply by email saying that the problem was a thrust bearing in the clutch! so he did get it checked out and if he did that in the first place when i asked i would have got the car. as a result i didn't want to touch any of his cars.

I will never go through any company to import a car again! it was a waste of money and my time!!

That must be pretty disappointing. But to be fair to the guy it may not have been possible for him to have the car fully inspected in JP. Unfortunately importing cars is a risk - you win some, you lose some. Obviously the more conscientious your broker/buyer the more you'll win...

Richard

the car was a r32 gts

it was dissapointing but i was prepared for it, its not the first time things like this have happened. like you said, you win some you lose some.

mmmgtir- i am with you that he may not have been able to know every detail about the car and i had no problem with that at all. i was just unhappy that he was not reasonable with helping solve the problem or at least letting me find out what the problem was.

and thanx to homer2288

i had a quick look at the other cars he had in and they looked like they were driven here from japan, i saw one decient car and it wasn't worth what he wanted.

I know the guys at jspec organise a full inspection and report of the car on the customer's request if the car's bought thru a dealer or a yahoo auction. They have mechanics in most of the big cities they outsource to. Don't exactly know the pricing but I think the mechanic charges extra if he has to travel to a distant town or something. So something like that IS possible to pick up before the car lands here.

Funny thing is when a mate of mine rang Yahoo Motorsport his response was "sign up on J-Spec and Prestige's mailing list, if you see a car you like then gimme a call". So basically he sits on his arse n does fcuk all and gets money for filling out a few forms... At least his competition look for a car for you.

My car came in through Yahoo, a friend bought it from Yahoo then I purchased it from him because he didnt have time to finish registering it before his holidays finished.

Body was good apart from a couple of small things (badly bogged and painted smack on front right guard, holes in boot lid from big GT wing and some less than 100% paint but I couldnt care about that), engine seems to be in good health (made 124rwkw in shootout mode, manual S13 SR20DET with equivalent exhaust/filter made 113rwkw), diff seems nice and tight, adjustable shocks are tight and came with a few extra bits... Watanabes, KYB adjustables, HKS 3 inch and pod and a Jenesis front bar. Interior is pretty cacked but meh who gives a toss about that.

I think my car is a reasonably good example and doesnt seem to be anything like some of the stories I've heard about dodgy johns cars.

When I've got some spare cash Yahoo will be the first place I'll be looking for a Kei car, i figure my DR30 came out ok so I may as well give them a chance

cool thanks for the info, i didnt realise the "importing" game is so messy, i think ill try yahoo and imports 101 and see how it goes....if anyone else has constructive criticism about importers etc i wouldnt mind hearing about it....

Cheers

:headspin:

Importing a car's all about patience and trust, if you don't show your agent that then your importation experience will be really bad regardless of who you go with.

same here, picked up a blue 180sx, little scratches, spotless interior, jic coil-overs, damper and camber adjustable, few other bits. the CA motor is crisp as a mother. paid for it on the wednesday and got it on the monday following. im in melbourne. over all very happy with the service. TOUCH WOOD.

]]would anyone know a good cheap place to comply a 180sx here in East melbourne area

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...