Jump to content
SAU Community

Recommended Posts

Hi does anyone have any experience with Haltech E6K???Any comments. Technically on paper it seems to be good.How does it compare with say power fc?

Is it reliable and constant in its performance?

Is there any good haltech tuners in melbourne because i heard that its tuning software is quite complicated.

By the way does anyone have the address or telephone of Hypertech(formerly BGT) in Vermont South?

Thanks.... :)

Link to comment
https://www.sau.com.au/forums/topic/5195-haltech-e6k/
Share on other sites

Speedo, i know two people using the EK6 who are very happy with it, Lepperfish on these forums fitted one to his R33 GTST it it goes pretty well. It was fitted and tuned in Sydney, not sure about Melb but they certainly seem to be a good ECU

Might be worth chatting to some reputable import tuners in your area and seeing what ECU they recommend.

Link to comment
https://www.sau.com.au/forums/topic/5195-haltech-e6k/#findComment-79873
Share on other sites

Fitted one in a VL Commondoor with an RB-20 in it and tuned it with no real dramas. You can't really compare the Haltech with the Power FC, as the P-FC will plug straight in, ease on install is a lot easier. Haltech you need to pin off specific wires, or create a new harness for the engine.

Advantage with the Haltech is the cost, around $1,500.oo for the whole kit with loom, sensors etc. All you need to buy is a 2-Bar Map sensor.

Link to comment
https://www.sau.com.au/forums/topic/5195-haltech-e6k/#findComment-80302
Share on other sites

Speedo, what car do you have?

If your considering cost mainly then check out the micro tech. it may even be slightly cheaper than the haltech. You'll be able to plug and play if you have a 33.

Either way, from what ive seen from my car and others, there is little point spending the extra cash on a Power FC. Tuning with the FC hand controller takes longer than computer tuning and adds cost also, so ive heard.

Link to comment
https://www.sau.com.au/forums/topic/5195-haltech-e6k/#findComment-83317
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...