Jump to content
SAU Community

Recommended Posts

These guys aren't stupid, they've worked in the auto industry for many years and usually know exactly what they're looking at.

its pretty funny that you say that, cause the guy that engineered my car had no idea about my turbo. the compliance guys convinced him that it was just the stock turbo on a different manifold. he must have been stupid cause he believed him and signed it off.

Vic Roads wasnt a problem either. The guy actually put his hand on the turbo when he was looking for the egine number. :rolleyes:

the only tricky thing is RWC...

.

There are a lot of people that don't know their stuff, but then you will run into those that do. It only takes somebody that *does* along the way and you're in trouble. And things only get stricter each year. Seems to me you have about three options:

a) take it to another state and try and transfer the rego (two lots of rego, etc) and see if the engineers can be still valid.

B) remove the turbo and return it mostly to stock (probably best option).. although soon as you change it back the engineers is invalid, so is any insurance (including if you hit a person on the road), and you only have to get pulled over by a nice policeman in vic and you're back where you started.

c) pay off the right people ..

You don't have much other options to totally frank. VIC is *strict* - damn strict.. .on most things. Just remember when it comes to insurance the story will be exactly the same.

Fark that...

RWC and engineering certificate will all be done in VIC. I have seen a few T78 big single modded R32's on the roads in VIC. It is possible and it will be done! I now have a few good options and I'm going to keep the keyboard quiet untill it's done. VIC is strict and even more so since unfortunate crash yesterday... heard that all cops were sent memo to book all "imports" with P plates (which will mean all imports get anal probes for the next month or so P's or not)

there are a lot of illegitimate cars in melb.. many shouldn't be on the road according to any applicable law - but they are.. see point c) :)

also see point B) - if you get an EPA (very likely seeing as just about every VIC skyline owner has had one.. inc me when i was there).. and you will have to remove that turbo.. no two ways about it. And the EPA are the clueist people I have ever seen inspect a car - I guess if you see a few hundred skylines you tend to know what a completely stock one looks like.

Fark that...

RWC and engineering certificate will all be done in VIC. I have seen a few T78 big single modded R32's on the roads in VIC. It is possible and it will be done! I now have a few good options and I'm going to keep the keyboard quiet untill it's done. VIC is strict and even more so since unfortunate crash yesterday... heard that all cops were sent memo to book all "imports" with P plates (which will mean all imports get anal probes for the next month or so P's or not)

Does anyone know of a decent but reasonably priced compliance workshop in melbourne? I have a GTR coming with 2xGT2530's.. One workshop wants over $1500 to compliance the car, which i cant help but feel is a bit expensive,

Any help would be greatly appreciated :)

-Patrick

Does anyone know of a decent but reasonably priced compliance workshop in melbourne? I have a GTR coming with 2xGT2530's.. One workshop wants over $1500 to compliance the car, which i cant help but feel is a bit expensive,

Any help would be greatly appreciated :)

-Patrick

I only know of 2 and would recomend 1 - PM sent.

you safest to conver to tiwins for reg and engineering I always try to comly and reg my cars as stock as possible and they tend to go through quickly . my record for compliance and sign off is 2 1/2 days on the rb25 cef rwc was easy with it as well. if you want to play wit the big boys ie t78 you need to pay

cheers

Basically you are registering the car if it were new, so it would have to comply with ADR of the day. In other words your car would have to be a stock GTR R32.

If they wanted they could nknock you back for steering wheel, gear knob etc, etc ,etc.

Trying to legally get a T78 engineered and approved was a bit of an ask, when most people keep egtting defected for having a BOV.

????

If they can engineer and register turbo conversions in dattos, I don't see how a big single on a TT RB26 in a GTR is a problem.

Couple of differences:

- the emissions regs on older cars (eg datsun 1600's) are nowhere near as strict as on cars like GTR's

- engineering a turbo conversion requires a lot more work on the engineers part than an inspection to meet 15yo requirements. For example a full brake test would be mandatory (brake performance/fade, etc). In this case I've got no doubt the engineer has seen the single turbo, realised the car is not standard to a greater extent than he would otherwise accept, and decided he'd rather not take the risk.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...