Jump to content
SAU Community

OT: pics of all german car show 10/10/04


Recommended Posts

neo I would still own you around corners with my dead standard CL with its huge body roll and proven 18.6s 1/4mile time! :jk: (and it did own s13 ca18det around corners) However I wouldn't quite call a mk4 a go kart handling consider they weight around 1300kg :D

well if I ever get $$$ one day.. I wouldn't mind building a street trim golf fwd for 1/4mile race ;) just not sure whether to start with mk3 vr6 and then twin t or mk3+1.8t.. still leaning towards the 1.8t for less weight factor. Have heard that its possible to get 300kw@fly with headgasket change+bolt on with 1.8t, with traction permitted that should guarantee 12s :D oh then theres the dreadful fwd gearbox problem..

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Guest neoGT-25

Hey japtaxi, i would go the VR6 anyday!

i have some videos of a 10 seconds twin turbo one in the USA...

http://www.eiptuning.com/

this is the company who built both the 10sec MKIII VR6 and the 600HP .:R32 (the videos are on their site)

they sell some pretty top stuff... you dont want to look at the prices though!

I want to get their cold-air induction system and fmic... i really shouldent be driving to melbourne! I NEED MODS!!! ;)

do it... do it NOW plz :rofl:

seen it done already biggest prob is running the rad up the front U need a bull bar on it to cover the rad ;) but the one I have seen was a neat job & went well too little hard to punt it through a corner though :)

ah ok just checken I saw a little whit golf parked in the car park on one of the cruzes I went on though it might of been urs, nah get a set of ROH blade black chrome 18's for it that would really set it off + thay are not a very heavy wheel

Guest neoGT-25
ah ok just checken I saw a little whit golf parked in the car park on one of the cruzes I went on though it might of been urs, nah get a set of ROH blade black chrome 18's for it that would really set it off + thay are not a very heavy wheel

the wheels im talking about are these...

RS4.JPG

only my car is 4 door, and will have 35% tint

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...