Jump to content
SAU Community

10s R32 GTR?

The Jake

By The Jake,
in Engines & Forced Induction

 Share

Recommended Posts

GTR-Ben Proficient

GTR-Ben

Posted
Posted

GT2530's, cams, 720cc injectors,oil pump, ecu (good tune), intercooler, clutch, intake, exhaust..

Stock crank, pistons and rods. (best to upgrade them if you want it to last as well as the box.)

Running an OS box and holding 3rd (big revs..)

And some good driving can get you there. Without stripping the car also.

Need about 400kw at the wheels.

Seen low 10's with this setup + slicks and fuel pump upgrade. :D

Doesn't mean you can just bolt on all those parts and do it easy, nothing is easy.

Link to comment
https://www.sau.com.au/forums/topic/54204-10s-r32-gtr/#findComment-1062278
Share on other sites
GTR-Ben Proficient

GTR-Ben

Posted
Posted

Yes every one had doubt.. even me until it did it.

I was suprised with the high 10's on street tires, then it did a few low 10's. Best of 10.3.

Best run on the dyno was about 410kw.

I have had the engine apart so know what it has.

I can't say how long it would last pushing that setup to it's max... but it's still going.

I only had to replace one stock piston in it after a ring land was broken, so it even has a single second hand piston. :D

Got another one running a T88 34D and worked bottom end. Makes similar power, has half the responce. Has done a 10.6 in full street trim. Could go a lot better with a experienced driver.

Link to comment
https://www.sau.com.au/forums/topic/54204-10s-r32-gtr/#findComment-1062316
Share on other sites
NXTIME Grand Master

NXTIME

Posted
Posted
the best thing to do to get your r32 gtr into the 10s, is find someone who is selling a 11second gtr for cheap and install nos and bank your there.

That would work :rant:

But I wouldn't be content with that. I would want to run the numbers a few times and would like to improve them - not just run it once. I would also rather go for a twin turbo set up, even though most would say that a big single is cheaper, easier, etc. My mods would be:

- twin HKS 2835 turbo kit

- forged internals

- stroked bottom end (2.7-3.1L)

- MoTeC or Autronic ECU

- appropriate head work, 280° cams, adj. cam gears etc

- custom plenum, Infinity throttle body, 800cc+ injectors

- twin Bosch pumps, lift pump, surge tank

- drag spec cooler

- 6 speed dog box

That's just off the top of my head.

Link to comment
https://www.sau.com.au/forums/topic/54204-10s-r32-gtr/#findComment-1062434
Share on other sites
wreckedhead Mentor

wreckedhead

Posted
Posted
That would work :D

But I wouldn't be content with that. I would want to run the numbers a few times and would like to improve them - not just run it once. I would also rather go for a twin turbo set up, even though most would say that a big single is cheaper, easier, etc. My mods would be:

- twin HKS 2835 turbo kit

- forged internals

- stroked bottom end (2.7-3.1L)

- MoTeC or Autronic ECU

- appropriate head work, 280° cams, adj. cam gears etc

- custom plenum, Infinity throttle body, 800cc+ injectors

- twin Bosch pumps, lift pump, surge tank

- drag spec cooler

- 6 speed dog box

That's just off the top of my head.

waste of money for the motec, stroked motor, forged internals, custom plenum, twin bosch pumps and surge tank, you dont need all that stufff to run 10s,

all you would need is injectors, 044 fuel pump, cams, bigger turbo(s) power fc, cooler, standard box is fine, and some good slicks you should get into the 10s with a few passes, then after you get into the 10s then you have to spend big bucks to get back on the track.

Link to comment
https://www.sau.com.au/forums/topic/54204-10s-r32-gtr/#findComment-1062952
Share on other sites
Butler Proficient

Butler

Posted
Posted
waste of money for the motec, stroked motor, forged internals, custom plenum, twin bosch pumps and surge tank, you dont need all that stufff to run 10s,  

all you would need is injectors, 044 fuel pump, cams, bigger turbo(s) power fc, cooler, standard box is fine, and some good slicks you should get into the 10s with a few passes, then after you get into the 10s then you have to spend big bucks to get back on the track.

totally agree. it doesnt take huge uber dollars to get a 32R into the tens. A pair for 2530's/2540's/t518z's should do nicely and still have some acceptable response. fuel pump, cooler, cams, pfc or any other god ecu, clutch, injectors, some good tyres ( maybe nittos if you can find them or even federals as a 32 cracked into nines with these!). all you have to watch out for is the box!

Link to comment
https://www.sau.com.au/forums/topic/54204-10s-r32-gtr/#findComment-1063005
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted
Big difference from a car that runs one 10 sec pass, to a car that runs constant 10's at every meet without breaking

i totally agree 100%

to build a car thats going to last isnt cheap.

building one that does a few blinders one night and never goes back to the strip...

thats easy

Link to comment
https://www.sau.com.au/forums/topic/54204-10s-r32-gtr/#findComment-1063084
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...