Jump to content
SAU Community

Recommended Posts

So im eating dinner and I see on the news that there has just been a 22 car pileup with multiple casualties on the F3. They didnt say where or which direction but it sounds very bad.

Hopefully no sau'ers or people we know were involved in this incident.

Anyone got more information?>

/Edit: http://www.news.com.au/common/story_page/0...55E1702,00.html

Link to comment
https://www.sau.com.au/forums/topic/54252-22-car-pile-up-on-the-f3-tonight/
Share on other sites

"A 45-year-old Gosford woman who was airlifted to Sydney's Royal North Shore Hospital had suffered serious limb fractures and minor head injuries"

damn work right next to the hospital never noticed ahelicopter though

hope everyones ok, and no sau or sau friends hurt in the accident

Apparently the lady who was killed, was travelling north and was stopped behind the car pile up. Then a loaded semi ploughed into the back of her and killed her instantly when the car burst into flames.

I was driving the opposite direction back to Sydney that night and saw the aftermath.

Flashing lights everywhere but looks like it had been cleared up a bit.

ALL traffic diverted heading north and 1 lane closed as we travelled south.

You could see tyhe front of the semi that hit the car. Even the semi was F%*&ed up.

I would have to say it would have been the fog that did it. Was a shocker!

The lady probably stopped like the previous posts said but the semi would have been flying through at the 110 kms and just wacked straight in before being seen.

Fog is usually at it's worst on that section.

By the way, it was the very bottom of the Mooney Mooney bridge where i would guess people are going the fastest.

  • 2 weeks later...

I was a passenger driving down the mooney mooney bridge on sunday afternoon and the display of carnage left shown by the yellow police markings were enuf to say that it was one mutha of an accident..No shit it started at the start of the bridge or there abouts and it didnt finish untill about half way accross.That turck and driver were absolutly motoring to cause that much carnage.

Did you hear the latest from the past few days?? The truck that plowed through the pile up of cars was uninsured and unregistered! There was over $800k damage. He has got to be looking at a jail sentence for sure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...