Jump to content
SAU Community

Recommended Posts

hey,

Today my car started making a ticking sound (loud, very audioable when driving) from the turbo side of the engine. It happen when on gas, fast, slow whenever i am on the gas i hear the sound, also if i put the foot down and go up into the rev range it sounds like its getting faster. It doesnt do it on idle, thou if i rev it it sounds to only make it around the 3/4000 rpm mark (the same spot my bov starts going off)

Now with all this in mind, on monday, my Oil line from my turbo to engine blow (was rubber not metal -- dont ask me) now i lost 4L of oil, my mech replace the line with a stock metal rb line, refill with oil and the car was given the OK that everything was working

Now from my limited knownage, i think it might be the turbo, its boosting fine and making power but it sounds like the ticking is related to the spinning of the turbo wheel (guess?)

I will have the car check out on monday (or maybe 2morrow), But if i cant get it in 2morrow it will wreak my head in untill monday can anyone help

thanks mike :D

Hey

I've had the same problem with my car. Does you car have a full exhaust system? This normally happens when you have a cat-back exhaust. You build too much pressure and you blow out one of the gaskets. So as you rev higher you can hear it louder as it is leaking more air. Try getting an exhaust specialist out. Are you in sydney? Give me a yell if you are! Got someone that can help!

Phil

Yeah most likely its gonna be the one of the gaskets. I've blown one before and in the verge of blowing another one. Just get your car checked out by an exhaust specialist. It should cost around $300 mark. If you know the guy you might get it cheaper!

If it was the turbo it would be a very fast noise, almost a buzzing but if it is a ticking and you lost that much oil I'm considering a big end bearing. Get it checked fast and don't drive it unless you have to. The bearing and journal can sieze causing a conrod to snap which will destroy your engine.

Sorry if it sounds over the top but it isn't worth destroying an engine. I had one in mine and the ticking/tapping noise was quite loud in the garage and seemed louder on the left side.

Drop the oil and look for golden coloured metal specs and flakes. If they are there a bearing is going. In that case a rebuild is needed, probably with a crank and conrod big end grind. Sorry to say will be expensive if it is but you get to rebuild a decent engine that will last ages.

I hope it is not that bad but from what you say, it seems pretty clear.

michael ,

it sounds like a big end sorry to say mate .

do this little test . when the engine is cold ( stone cold ) start it up and listen for the noise, it should be very mild while the engine is cold ( thick oil takes up the slac on the bearing ) .

when the engine and oil gets to normal operating temp the noise will get louder , if thats the case then its a big end .

michael ,

it sounds like a big end sorry to say mate .

do this little test . when the engine is cold ( stone cold ) start it up and listen for the noise,  it should be very mild while the engine is cold ( thick oil takes up the slac on the bearing ) .

when the engine and oil gets to normal operating temp the noise will get louder , if thats the case then its a big end .

ok i just did that test, the sound is louder when the car is cold, when the car comes to normal oil/rpm/temp it becomes very quite and u can bearly hear it. give the car a few revs and it comes back for a few seconds :s

i am very confused

exhaust leak, most probably the manifold bolts/studs loose or broken or about to break.

tighten the bolts up, but there is a fair chance that some might break so take care.

Apparently this is a common flaw with the rb engines - dodgy exhaust manifold bolts!

exhaust leak, most probably the manifold bolts/studs loose or broken or about to break.

tighten the bolts up, but there is a fair chance that some might break so take care.

The botls snap.. I had EXACTLY the same thing happen to me at wakefield park. Turns out my exhaust manifold had a slight warp in it and had snapped 6 of the bolts. Its very common on skylines

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...