Jump to content
SAU Community

Recommended Posts

yep Matt I had 330rwkw never got to run it with the more power though before it dropped the ringland, to be honest all my 60ft's were bad hahaha that mph was done doing 2.0 60fts even with a 2.1-2.2 it didn't change more then 2-3mph

Cheers for the info mate. Sounds about right to me - 2.1-2.2 60' and mid 120's with 420rwhp (313rwkw).

RNS11Z and my results are fairly close to. Same mph and similar power 'at the time'.

  • Replies 196
  • Created
  • Last Reply

Top Posters In This Topic

I can understand why people are getting frustrated with Steve.

He is saying 'we can do XXX with stock injectors' when it goes totally against all therory, and he won't give any hints as to how he has done it.

So what sort of responce does he expect when he won't give any details. This is a information sharing site after all isn't it ?

I think he just likes stiring the pot.

Also, just because the stock injectors are sitting in the rail doesn't mean they haven't been modified in some way.

J

I can understand why people are getting frustrated with Steve.

He is saying 'we can do XXX with stock injectors' when it goes totally against all therory, and he won't give any hints as to how he has done it.

So what sort of responce does he expect when he won't give any details.  This is a information sharing site after all isn't it ?

I think he just likes stiring the pot.

Also, just because the stock injectors are sitting in the rail doesn't mean they haven't been modified in some way.

J

werd

The thing is if the car goes and does 128-131 mph trap speed everyone here will acknowledge yup that sounds about right, the time itself isnt too important, therefore the setup isnt either. However if it goes and does a 12.2 at 120 we are all going to be thinking hmm sounds a bit low, no matter what excuses are used.

whatsisname, correct. How ever when i ran my car down the 1/4 it was only making 345rwhp (not a dd dyno and not in shoot out mode).

The thing that confuses me is how steve manages to get such power from a gt30 at low boost. When i had my gt30 i had to boost it to 27psi to get to 430rwhp (non shoot out mode). On 23-4psi it made 387rwhp using stock injectors (non shoot out mode). I never had a chance to run it when it was at full potential. I think either steve has figured how to tune 25's with a gt30, or something fishy is going on, or my tuner had no idea!

Magic1's car should run easyly over 120mph if he is making over 400rwhp. Good luck to him and hope he does well to shut some of us up.

H.

answers for all.

R31NISMOID. Not sure of the rear housing, but it was sold to me as a 500hp turbo. increasing the boost saw no gain in the power. so its flowed!

Sydneykid. I must say that you have a very active brain :( , why dont you come to perth and have a look for yourself or do you have a trusted friend here to look for you?

I have had bugger all exprience drag racing, i need more practice. I will be running slicks when it goes to the track as the Motorplex preps their track for rubber based tyres not silica based tyres. thats the only change, i will even have the spare tyre in. My shockies and springs are nismo and are not soft nor drift spec hard, track spec if i had to choose. these will also stay so.

BBQ. 6 injectors, no nos, straight bp 98

Pics yes, dyno yes, video of dyno yes, slicks, see above.

Roy. why dont you come to perth and have a look for yourself or do you have a trusted friend here to look for you? Lets have a close look in the airport carpark after i pick you up. no mechanic, im not. i will bring beer, whats your fav.

RNS11Z. You are a champ, cant remember you nave but who can forget Brisvegas. Cams help bring the gt30 on early and hard. Did i say that your a champ.

Regards

Tristan

Please answer my questions.

Can't wait to see how it goes on the drag strip Tristan. Bottom line... enjoy what will be a fun day/night at the drag strip, especially as it appears to be your first time.

Regardless of suspension set-up and your best ET it should still run some fairly decent mph. I would have thought 130mph should be easy enough, given the current power level.

GT30s make there power at around 22psi.

Lets wait till wed week when the car goes to the plex and yes anyone that wants to come here is more than welcome to take the injectors to a test bench to see if their modded.

PPL will cry but to remove excuses Sean tippet(GOTBOOST) is the driver for the nite at the drags.

Have the injectors been hi-flowed? May have been answerd, but i must have missed it.

Is the car allways tuned to that power level every day or was the fuel pressure/boost wound up just to achive 511hp on a ' few ' dyno runs. If not what is the day to day power level/boost/fuel pressure?

Steve SST, no one is having a go at you, we are all just trying to further out knowledge and figure out how we car save some dollars on the way. A great result none the less with the tune, just most people would like to see how you do it with stock injectors. We all just want to see how you do it, and when you say you dont want to tell (sure you may have your own reasons as being a workshop), people start to doubt the result without a sound explanation. How does posting a result with no explanation further the knowledge of anyone.... ? I'm just want to learn, teach me, show me, show us, share the knowledge for the greater good, haha.

WD Magic1, must be an awsome car to drive around on the street, i cant wait to see you run a 1/4 mile, i bet you'll have heaps of fun doing it aswell. Steve SST, well done on getting that sort of power with stock injectors, personaly in your professional opinion do you think it is safe to leave the car as is with the injectors and power level it is running?

Once again well dont steve/magic, very impressive result.

Injectors are stock and yes Tristan is driving this car every day as a real estate agent as it runs on the dyno.Lets get this right 511rwhp is total bullshit but ppl with dynapac dynos say they are the only dyno that is right.450rwhp is our max we have had long term from stock injectors on our shootout dyno.

nope a twin plate bought off this very site from MR33, thanks again MR33

BBQ. 511 is bullshit, i laughed when it flashed on the screen.

Ok well how come the original post is:

The R33 GTS of Magic1 from these forums ran 511rwhp at PAS western salon today on Speedworks Dyno.

This car is an RB25 with Arias pistons GTR rods and 256/264 HKS cams using a GTR cooler and Wolf plugin ECU  and a GT30 Garret turbo but still has stock injectors and intake manifold but Sard reg and 044 pump.

We tuned it to 20psi and 11-1 afrs running pump BP98 fuel.

How much power did the motor put out ? As the original thread states 511rwhp ?

Injectors are stock and yes Tristan is driving this car every day as a real estate agent as it runs on the dyno.Lets get this right 511rwhp is total bullshit but ppl with dynapac dynos say they are the only dyno that is right.450rwhp is our max we have had long term from stock injectors on our shootout dyno.

450rwhp is where it is at. Why. other components are falling over or reaching capacity first. Namely the turbo and con rods on my car, we are not even sure if the standard pleum is holding up proceedings like wise the r34 gtr cooler.

BBQ. Please do read the whole thread the answers lie within. I have the new dnyo chart in front of me and it will be posted tonight.

Patience is a virtue

Well unfortunately the original thread was stated that you made 511hp with stock injectors, Now your saying that you only made 450, and the fact that this thread is now 6 pages going on to 7 pages long, makes it a little harder to find the correct answer. So basically you didn’t make 511 Hp as Steve has stated, which he should go back an re-edit the post to the correct figure. Because thier is a big difference between a car that makes 450 hp and a car that makes 511hp.

BBQ. 7 pages, shortest book i have ever read. It did make 511rwhp on speed works dyno at Perth Western Salon, it did win its class and came second overall only to a dyno queen car. a 6l supercharged v8 came third. It was in a dyno comp and on the day all cars were measured on the same dyno. all we are stating is that

1. It was not a shoot out mode dyno

2. I dont believe the figure, it great and if i was selling the car.

3. speedworks would hold a bible to my car being 500+hp

Dyno dynamics invented shoot out mode to avoid this and it should be the standard, how do you enforce it though?

no editing needed.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...