Jump to content
SAU Community

Recommended Posts

hey guyz im just asking a question on behalf of my mate, he has a auto 1995 r33 with a fmic and he is wanting to make more power out of it with the usual mods exhaust, fuel pump etc but he was wondering how strong the auto box is? stronger then a manual? and if anyone on here has a auto making some power how much and are they reliable?thanx ;)

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/
Share on other sites

my lines auto and pullin 208.9rwkw and like my number plates suggest it gets kicked in the guts every day

the only things that are wrong with mine are

coilpacks

ignitor coil

starter motor

alternator

oxygen sensor

(((((Think it was struck by lightning))))) jokin just a lemon

but except for the coilpacks and ignitor coil these are pretty auto unrelated problems

that will be fixed on tuesday

i am also curious about the spool up in snow

i usually rev it upto about 5000rpm in nutrual the slam it into first

but only in the wet or when racing and only cause i can get a replacement gearbox for free

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077408
Share on other sites

My auto is running strong at 200rwkw.

For serious questions about whats possible and how it should be done, ring MV Automatics in Adelaide. They added a trans cooler and shift kit to my auto and gave me the impression they were good for close to 300rwkw. There are mods you can do if you are running an auto with over 300rwkw.

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077725
Share on other sites

My auto is running strong at 200rwkw.

For serious questions about whats possible and how it should be done, ring MV Automatics in Adelaide. They added a trans cooler and shift kit to my auto and gave me the impression they were good for close to 300rwkw. There are mods you can do if you are running an auto with over 300rwkw.

Did your car come with a transcooler? or did you just upgrade to a bigger one?

What did the shift kit contain btw?

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077811
Share on other sites

Lukits01 - yes my car came with a cooler, but I had a bigger on installed. (like the standard intercooler but on the drivers side)

I am not sure what the shift kit contained as it was purchased and installed by MV automatics. Shifts are now a lot tighter when under acceleration, and the tyres chirp during gear changes.

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077951
Share on other sites

yea i have found that a big trans cooler makes the world of diffrence my R32 did not have one it just cooled through the radiator piss poor. My R33 all ready has one but it's so small i will be changing it out next week i will be expecting the same change

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077965
Share on other sites

Push the snow button put food on the brake and stall it up - wheels wont spin because its in second gear and when your ready to take off press power and let go of the brake at the same time time and you get some interesting launch's :D usually wheel spins off the mark dont do it too much cos the clutch packs dont like it (As i found out)

I put a 5 speed in it after it blew up and never looked back.. even though im having troubles now as the Pedal box broke under the clutch cos of sydney traffic and a heavy clutch.

But yeah cars i was just beating before in the auto - I was smashing them in the 5 speed - remember that auto dif ratio's are 4.39:1 where manual is 4.11:1 so you will be quicker off the mark then the 5 speed released skylines.

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077969
Share on other sites

A good auto will still change gears faster than a manual, and will consistently do it at the correct RPM. Giver a choice and all things being equal the auto should always beat a manual.

NB - I am assuming the manual has an upgraded clutch and the auto has had a shift kit, and that both cars have similar power.

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1078154
Share on other sites

Changed automatic fluid today, car feels alot smoother and a little faster :)

it took me awhile cos i took the transmission cooler off and gave a full degrease, flush and replaced all the rubber hoses.

I removed the in pipe from the cooler and attached a length of hose, then turned car on and watched it spray out :(

Fluid was horrible! When i check it every now and then with the dipstick its been a perfect pink color, but once it was out in a bucket it turned out to be a brown color (not because of the color of the bucket :( )

I managed to drain 4L on the dot, going to redrain again next week.

Used castrol transmax z $59 per 4L :kick:

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1079619
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...