Jump to content
SAU Community

Recommended Posts

hey guyz im just asking a question on behalf of my mate, he has a auto 1995 r33 with a fmic and he is wanting to make more power out of it with the usual mods exhaust, fuel pump etc but he was wondering how strong the auto box is? stronger then a manual? and if anyone on here has a auto making some power how much and are they reliable?thanx ;)

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/
Share on other sites

my lines auto and pullin 208.9rwkw and like my number plates suggest it gets kicked in the guts every day

the only things that are wrong with mine are

coilpacks

ignitor coil

starter motor

alternator

oxygen sensor

(((((Think it was struck by lightning))))) jokin just a lemon

but except for the coilpacks and ignitor coil these are pretty auto unrelated problems

that will be fixed on tuesday

i am also curious about the spool up in snow

i usually rev it upto about 5000rpm in nutrual the slam it into first

but only in the wet or when racing and only cause i can get a replacement gearbox for free

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077408
Share on other sites

My auto is running strong at 200rwkw.

For serious questions about whats possible and how it should be done, ring MV Automatics in Adelaide. They added a trans cooler and shift kit to my auto and gave me the impression they were good for close to 300rwkw. There are mods you can do if you are running an auto with over 300rwkw.

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077725
Share on other sites

My auto is running strong at 200rwkw.

For serious questions about whats possible and how it should be done, ring MV Automatics in Adelaide. They added a trans cooler and shift kit to my auto and gave me the impression they were good for close to 300rwkw. There are mods you can do if you are running an auto with over 300rwkw.

Did your car come with a transcooler? or did you just upgrade to a bigger one?

What did the shift kit contain btw?

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077811
Share on other sites

Lukits01 - yes my car came with a cooler, but I had a bigger on installed. (like the standard intercooler but on the drivers side)

I am not sure what the shift kit contained as it was purchased and installed by MV automatics. Shifts are now a lot tighter when under acceleration, and the tyres chirp during gear changes.

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077951
Share on other sites

yea i have found that a big trans cooler makes the world of diffrence my R32 did not have one it just cooled through the radiator piss poor. My R33 all ready has one but it's so small i will be changing it out next week i will be expecting the same change

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077965
Share on other sites

Push the snow button put food on the brake and stall it up - wheels wont spin because its in second gear and when your ready to take off press power and let go of the brake at the same time time and you get some interesting launch's :D usually wheel spins off the mark dont do it too much cos the clutch packs dont like it (As i found out)

I put a 5 speed in it after it blew up and never looked back.. even though im having troubles now as the Pedal box broke under the clutch cos of sydney traffic and a heavy clutch.

But yeah cars i was just beating before in the auto - I was smashing them in the 5 speed - remember that auto dif ratio's are 4.39:1 where manual is 4.11:1 so you will be quicker off the mark then the 5 speed released skylines.

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1077969
Share on other sites

A good auto will still change gears faster than a manual, and will consistently do it at the correct RPM. Giver a choice and all things being equal the auto should always beat a manual.

NB - I am assuming the manual has an upgraded clutch and the auto has had a shift kit, and that both cars have similar power.

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1078154
Share on other sites

Changed automatic fluid today, car feels alot smoother and a little faster :)

it took me awhile cos i took the transmission cooler off and gave a full degrease, flush and replaced all the rubber hoses.

I removed the in pipe from the cooler and attached a length of hose, then turned car on and watched it spray out :(

Fluid was horrible! When i check it every now and then with the dipstick its been a perfect pink color, but once it was out in a bucket it turned out to be a brown color (not because of the color of the bucket :( )

I managed to drain 4L on the dot, going to redrain again next week.

Used castrol transmax z $59 per 4L :kick:

Link to comment
https://www.sau.com.au/forums/topic/55159-auto-reliability/#findComment-1079619
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...