Jump to content
SAU Community

R34 GTT stock wheel size? Fit R32?

B0oStEr
 Share

Recommended Posts

B0oStEr Mentor

B0oStEr

Posted
  • Author
Posted

I've tried to measure the offset of my stock R32 rims. It's a bit hard to be sure on the car but they seem to have 40mm offset.

If my 6.5" R32 rims are 40mm offset and Gtt rims are 7" would 35mm be near the ideal offset?

Does anyone know what the actual Gtt offset is?

B0oStEr Mentor

B0oStEr

Posted
  • Author
Posted
They are 7.5 wide not 7.

Stock tyre size is 225/45/17.

Offset is roughly 35 front, 38 rear. - May want to double check that

Are you sure the offset is different front to back?

I bought a set of GTT rims today and they are all the same. The offset seems to be 39 or 40mm. It's a bit hard to measure to the mm with the tyres on.

From outside to outside the rims are 22mm wider than my 6.5" R32 rims so yeah, they are probably 7.5".

Anyway they look like a 100% legal upgrade for the R32 :)

NJR 34GTT Proficient

NJR 34GTT

Posted
Posted

Yes i was wrong about the offset. That was the offsets for 18x8 and 18x9 to fit my car. Nfi why i remembered at the time that they were stock offsets.

But yes they are most definitely 7.5 wide. Tyre placards etc state it.

B0oStEr Mentor

B0oStEr

Posted
  • Author
Posted

I tried fitting them today.

Julzz was right, the fronts don't quite clear the TypeM caliper.

A 3mm spacer would fix it but aren't these illegal?

They only just touch as you fully tighten the wheel nuts.

Actually there would be plenty of thickness in the caliper to shave about 2mm off the edge that touches the wheel.

Is this too bodge?

  • 3 years later...
Rekin Grand Master

Rekin

Posted
Posted
I tried fitting them today.

Julzz was right, the fronts don't quite clear the TypeM caliper.

A 3mm spacer would fix it but aren't these illegal?

They only just touch as you fully tighten the wheel nuts.

Actually there would be plenty of thickness in the caliper to shave about 2mm off the edge that touches the wheel.

Is this too bodge?

majority of people shave off the Nissan wording on the caliper, this usually gives enough clearance for the rims.

id prefer to do that instead of spacers, as spacers are illegal.

WET-25T Collaborator

WET-25T

Posted
Posted
majority of people shave off the Nissan wording on the caliper, this usually gives enough clearance for the rims.

id prefer to do that instead of spacers, as spacers are illegal.

Mine didnt touch the nissan logo, it was far from it. It was hitting the whole edge of the caliper when the tyre was rotated.

  • 2 weeks later...
bubba Grand Master

bubba

Posted
Posted

I have 34gtt rims on my 32gtst, they are 7.5" wide. I'm running 225s on the front and 245s on the back.

Initially had to run a 3mm spacer on the front as the rims bound up on the brakes, when I changed to 33gtst brakes this problem went away and I didn't need the 3mm spacer (there is barely 1mm of clearance though).

  • 1 month later...
siddr20 Grand Master

siddr20

Posted
Posted (edited)

I have fitted r34 gtt rims onto a r33 gtst with no problems at all.. No need for spacers etc

However it might be ideal putting 3mm spacers on.

offsets are 38 (so i have read on these forums in the past threads)

I dont see why it wont fit a r32.

They got smaller brakes right? compared to 33s? if so then will fit perfect

I have seen pics of 32s with 34 gtt rims :P

bubba- WOW you got 245s on a 7.5inch width rim?? how? lol

thought 235s would be the most..

Edited by siddr20
siddr20 Grand Master

siddr20

Posted
Posted
Mine didnt touch the nissan logo, it was far from it. It was hitting the whole edge of the caliper when the tyre was rotated.

Yup same here.

however, its like a mm off from touching.

Rims still rotate freely!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 persistent issues. P/steering and lag/misfire

      By GTSBoy · Posted

      Power steering is probably because someone has nuked the HICAS CU and you no longer have the variable power asist doing what it is supposed to. How much boost are you running? You are aware that any more than 10 psi on the stock ECU is just asking for it to go to full R&R (that's Rich & Retard, which is effectively Retarded and Retarded!) which kills all the power. Depending on the exact conditions, it can just be runnign on the fat and stupid end of the maps, then the conditions change, you make a little more boost and the ECU goes into panic.
    • Kapr
      Freddy Plenum vs Genuine options RB25

      By Kapr · Posted

      @BuiltNotBought Just as GTSboy said.   If you want driveabilty and more low down torque..keep the stock runners. They are VERY good from a factory. I have them too on my RB25DET NEO and as a GTSboy i have fmic but with stock piping route(i have Blitz intercooler) Iam making around 320 BHP and the car pulls "hard" from like 2,5k all the way to 7k. I have it dyno tuned to mimic N/A power curve and making little less max torque due to the smallbox tranny. But driveability is very great. I had 350Nm below 3k so car feels very quick.   EDIT:  Not my channel but i saw this and i know that is what i want (and i have exactly this)  
    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      Looking to sort out a couple of issues on my skyline  It recently was rebuilt, however rebuilder long story short did not give two flying effs about the work he did. So moving forward it's running but I have two persistent issues 1) it has a misfire / lag type of issue (was at higher RPMs but I had a dead piggy back ecu removed which improved it) now it's not as bad but still does it at random, I thought it may have been a boost issue I'm running an older turbosmart dual stage controller, turbosmart told me to try running off gate pressure however it still has a lag at random times. It has New MAF, maf plug, coil packs, sparks, CP harness.. injectors tested and cleaned. Factory ECU. 2) Power steering issue. It is tight as anything. Flushed power steering, rebuilt my pump because the bearing was shot. Flushed again still tight (mainly when parking and going slow into my driveway etc)  No kinks in hard lines, replaced the lines I could see had cracks. Still tough to steer.  I was told to shim a coin and place into the solenoid plug? Is there anything else. My steering angle sensor also has a issue. It's a used one I replaced, does it need to be calibrated? I feel like I've tried everything and this car is my voodoo doll.   
    • Dose Pipe Sutututu
      Neil's R33 Gts-t Build

      By Dose Pipe Sutututu · Posted

      Holy shit... wow!!! I totally missed this
    • MBS206
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By MBS206 · Posted

      One main filter. Each tank has a prefilter to keep rocks and small children out, then the big main filter that also does water separation. Clogged the first one so bad it was like a rev limiter at 3200rpm. Literally just like dropping the throttle off and maintaining rpm!
×
×
  • Create New...