Jump to content
SAU Community

Recommended Posts

Originally posted by adam 32

lowest structural part has to be 100mm off the ground (this is normally the chasis rails) remember the exhaust is NOT structural and therefore doesnt count...

see your pm for full detials

Are spoilers classed as structural? and what about clearance from the top of the tyre to the body? If any one can clarify this it would be much appreciated as there is a LOT of uncertainty with measurements and clearance heights!

Link to comment
https://www.sau.com.au/forums/topic/5636-got-my-car-today/#findComment-85357
Share on other sites

Originally posted by GR33DyMANGO

all i can say is totally radtech! heeehe

Radtech??:confused: ahh maybe im just gettin old

BTW: whats a good paint job like that worth? i could 'prolly' (i use the word tenatively) do it myself but i prolly couldnt be assed:drooling:

Link to comment
https://www.sau.com.au/forums/topic/5636-got-my-car-today/#findComment-85475
Share on other sites

daniel

there are 2 measurements that are commonly used, ground clearance and centre of axel to wheel arch.

1) the car must be 100mm off the ground from any structural point, bodykits are not structural. normally the lowest point is the chassis rail.

2) there is a certain distance that needs to be met on every car from the centre of the axel to the wheel arch. on R32's (when i had to go thru compliancing) it is 350mm. this varies from car to car and is about 10-20mm lower than the std height.

when going over the pits it depends alot on the overall presentation of the car, if it is a fairly tidy looking and 'tastefully' modified car then you can normally slide through. They tend to pick on riced up cars which are rediculously low or loud...

Link to comment
https://www.sau.com.au/forums/topic/5636-got-my-car-today/#findComment-85497
Share on other sites

Guest GR33DyMANGO
Radtech?? ahh maybe im just gettin old

haha.. my friends made it up when were skating at the leederville skatepark about 8 months ago. my mate skated around it a motorbike jacket and helmet looking totally homo.. we all laughed and someone called him radtech. if u r REALLY radtech.. then you;re radtech invincible.. haha.. sounds pretty silly.. but it has too many memories.

then last week.. my little brothers friends have this tv show on channel 31, mondays at 7.30pm called EXTREME WA... and they said radtech about 8 times.. we;re all trying to make radtech a new 'cool' word.. haha.. we do some pretty crazy things.. hehe..

Link to comment
https://www.sau.com.au/forums/topic/5636-got-my-car-today/#findComment-85529
Share on other sites

Well hopefully they look upon my car favourably :P

I really can't be bothered with those sorta hassles.

It's only really got an exhaust and it's not loud at all so I should be ok. Doesn't even have a pod filter :D

Tomorrow morning will tell hehe :P

Cheers for the kind words Justino :D

Link to comment
https://www.sau.com.au/forums/topic/5636-got-my-car-today/#findComment-85589
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...