Jump to content
SAU Community

Recommended Posts

Wouldnt it make no difference how many BOVs are fitted in relation to holding boost?

1,2, 5 or 10 of them fitted I thought would not give any increase in boost holding ability.

e.g If you had one of the plastic Bosch BOV and it leaked at 10psi I thought fitting another one would result in both of them leaking at 10psi?

I always thought the reason for having more than one BOV was for when running higher boost levels (36psi) it gave more total cfm release as only one fitted would struggle to vent all the excess pressure/air?

Wouldnt it make no difference how many BOVs are fitted in relation to holding boost?

1,2, 5 or 10 of them fitted I thought would not give any increase in boost holding ability.

e.g If you had one of the plastic Bosch BOV and it leaked at 10psi I thought fitting another one would result in both of them leaking at 10psi?

I always thought the reason for having more than one BOV was for when running higher boost levels (36psi) it gave more total cfm release as only one fitted would struggle to vent all the excess pressure/air?

They would just share the pressure.

Each would pass half the air a single unit would vent.

Get two coke cans, shake them.

Poke one hole in can A.

Poke two holes in can B.

The pressure of the liquid ejected from Can B, will be half the pressure ejected from Can A.

Twice the total CFM, half the pressure.

They would just share the pressure.

Each would pass half the air a single unit would vent.

No Each would pass half the air of one.

As the BOV is set at a X pressure they would release at the same time

under the same pressure but would escape twice as fast

Get two coke cans, shake them.

Poke one hole in can A.

Poke two holes in can B.

The pressure of the liquid ejected from Can B, will be half the pressure ejected from Can A.

Twice the total CFM, half the pressure.

Cant use the can theory here. Its Not the same as BOV as the BOV is pressure set.

Twice the CFM but same pressure as a single BOV.

:D

__________________

To combat boost holding problems, dont companies have varying strength springs that you can install? My cousins 1JZ's blow off valve had a different spring in it, so it would blowoff at lower pressures because he was running low boost...

The spring constant determines how hard a spring is, get a stiff spring fabricated to suit?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
×
×
  • Create New...