Jump to content
SAU Community

Recommended Posts

I have a pfc in my gtr and i am very happy with it ,people say the hand controls time consuming but you need laytop to change anything on most others and the metering by handcontrol is extremely handy to someone like myself as with pikehold and map tracking i can learn a lot from a run down the slip or lap of circuit etc. and the only thing they put against it is afm well spend a couple of hours with some well made piping and you'll never have to think of them again cruise and idle control are awesome even when i'm tuned to over 500hp it purrs like a kitty .

two of my good mates have just ordered pfc for there gtrs in group buy $987 to your door

so i think your mad if you look past pfc for a street gtr

pete

  • Replies 125
  • Created
  • Last Reply

Top Posters In This Topic

Don't want to side track this thread, but quickly, what is rotational idle??

Drops a different cylinder out for each crankshaft revolution by dropping the fuel at that cylinder.

Doesn't fire so cools down that cylinder quickly.

Very few computers can do that and none of the ones on this thread can( in PandP form ).

Cheers

Ken

The Wolf3D in Plug'n'play can't do rotational idle ?

Is the non PnP model more expensive ?

I'm sure this is gonna bite me but the non pandp wired into the car and tuned will be virtually the same money as an Autronic SMC.

Some shops love em , some hate em .

We like the Autronic product and have good success with it.

BTW , the fastest street S13 silvia in WA runs one.....

Cheers

Ken

I'm sure this is gonna bite me but the non pandp wired into the car and tuned will be virtually the same money as an Autronic SMC.

Some shops love em , some hate em .

We like the Autronic product and have good success with it.

BTW , the fastest street S13 silvia in WA runs one.....

Cheers

Ken

Ken lah..

does this mean there are 2 types of Wolf3D, the PnP and the other version and the PnP does not have all the features?

Ken lah..  

does this mean there are 2 types of Wolf3D, the PnP and the other version and the PnP does not have all the features?

Yep but go here for the answers.

http://www.wolfems.com.au/home

Cheers

Ken

Simon, read my post above re. rotational idle.

Autronics does it , Motec does it, Link does it

Wolf does not do it and never has....

Cheers

Ken

Are you sure you have been wrong before.

Anyone that wants a demo on rotational idle come in we have it sorted right now.

*Sigh*

I knew this was gonna happen.

As per my post re how rotational happens on most computers , that is it drops an alternate cylinder each rotation.

Does the wolf do that?

Or does it just hunt up and down as per 2 of the ones we have had in here?

I have no intention in getting into a war over this Steve and if thats what the Wolf calls rotational idle then that's fine.

Would be better to get the customer to compare it with an autronic , motec or Link rotational and make there descision from there.

On the Wolf website where does it mention rotational idle? This is purely a question and not having a go at you.

As has been stated on previous threads before, if the information is shared around amongst the tuners in Perth then everyone could benefit from the increased knowledge of the product .

The keeping of the information to the main dealer in WA makes it hard for the rest of the shops to tune these things to the best of there capabilities.

Cheers as always

Ken

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I don't think there's any way someone is push starting this car.. I honestly can barely move it, and moving it and steering it is just flat out not possible. I'm sure it is, but needs a bigger man than me. I have a refurbished starter now. The starter man was quite clear and consise showing me how nothing inside a starter really should contribute to slow cranking, and turned out that for the most part... my starter was entirely fine. Still, some of the wear items were replaced and luckily it didn't show any signs of getting too hot, being unfit for use, etc. Which is 'good'. I also noticed the starter definitely sounded different, which is a bit odd considering nothing should have really changed there.... Removed and refit, and we'll pretend one of the manifold bolts didn't fully tighten up and is only "pretty" tight. GM only wants 18ft/lb anyway. I also found a way to properly get my analog wideband reading very slightly leaner than the serial wideband. There's Greg related reasons for this. The serial output is the absolute source of truth, but it is a total asshole to actually stay connected and needs a laptop. The analog input does not, and works with standalone datalogging. Previously the analog input read slightly richer, but if I am aiming at 12.7 I do not want one of the widebands to be saying 12.7 when the source of truth is 13.0. Now the source of truth will be 12.65 and the Analog Wideband will read 12.7. So when I tune to 12.7 it'll be ever so slightly safer. While messing with all of this and idling extensively I can confirm my car seems to restart better while hot now. I did add an old Skyline battery cable between the head and the body though, though now I really realise I should have chosen the frame. Maybe that's a future job. The internet would have you believe that this is caused by bad grounds. In finding out where my grounds actually were I found out the engine bay battery post actually goes to the engine, as well as a seperate one (from the post) to the body of the car. So now there's a third one making the Grounding Triangle which is now a thing. I also from extensive idling have this graph. Temperature (°C) Voltage (V) 85 1.59 80 1.74 75 1.94 70 2.1 65 2.33 60 2.56 55 2.78 50 2.98 45 3.23 40 3.51 35 3.75 30 4.00   Plotted it looks like this. Which is actually... pretty linear? I have not actually put the formula into HPTuners. I will have to re-engage brain and/or re-engage the people who wanted more data to magically do it for me. Tune should be good for the 30th!
    • There are guys on Facebook under, Infiniti Owners Australia   https://www.facebook.com/share/g/1Z3RbPqx4k/?mibextid=wwXIfr What Whp are you after and I can help, and join this Q group in the states. https://www.facebook.com/share/g/19A59cN3JR/?mibextid=wwXIfr
    • Does any of you guys have instagram pages for your builds? Keen to see some Aussie builds. I still can't figure out how to post photos in here.
    • That awesome thanks for that. 
    • You can Remote any of these VR30..globally  Check: AMS Performance | Racebox | Sonic Tune | Soho | Z Motorsports | Specialty Z    Performance Parts | AMS | Z Motorsports | Boosted 6 |    Exhaust | Fast Intentions | ARK | MBRP Motordyne | Borla    There is someone in Sydney with 650whp   I am at 430whp without flex fuel, but FBO & Flex-fuel will push you to 500whp!!  
×
×
  • Create New...