Jump to content
SAU Community

** WSID 1st Dec **

MaTBoY

By MaTBoY,
in Events Archive

 Share

Recommended Posts

MaTBoY Grand Master

MaTBoY

Posted
  • Author
Posted

Because it's the way the world works!

I didn't get down there anyway, Due to the overwhelming response I thought I'd wait a week or 2 and see if we could get a group together to take over the place :P next one is next fortnight right?

Link to comment
https://www.sau.com.au/forums/topic/56978-wsid-1st-dec/#findComment-1108013
Share on other sites
  • 3 weeks later...
red900ss Grand Master

red900ss

Posted
Posted
alright I'll come along

will need to change my brake pads though cause I'll get some speed up before the turn 1 hairpin... so the sprints from the start line, round the hairpin to the burnout pad is it????

:confused:

bwahahah! :bahaha:

I'd like to see that!!!! :uh-huh:

Link to comment
https://www.sau.com.au/forums/topic/56978-wsid-1st-dec/#findComment-1137063
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...