Jump to content
SAU Community

Recommended Posts

Hi Guys

I have a friend who imports strut braces and I can get some good deal from him if I buy in bulk. This is the going rate

buy 5 for $70 each

buy 10 for $65 each

buy 15 for $60 each

buy more than 20 probably $55 each but we will see if there are that many takers.

Postage is usually $13

Here is the list of strut braces I can get

skyline

R33 front strut brace

R32 front and rear strut brace

Silvia

s13 front and rear strut brace

Supra

Fits JZ80 and 70 series front strut brace

Soarar

Fits on soarer twin turbo and non turbo front strut brace

If you guys are interested pm me or email me or reply to this thread.

Over the next few days/week I will see how many people are interested and let you all know what the cost will be. If everthing goes good I will then need the money from the buyers and I will get the parts and send them out to you guys. If everyone pays up quickly the buyers should get their strut brace within 7 days.

pictures

Link to comment
https://www.sau.com.au/forums/topic/57102-strut-braces-group-buy/
Share on other sites

Email has been sent to the guys interested. The brace are going for $65 each. If anybody is still interested let me know and I can try to squeeze you in aslong as it is before the end of the week. Otherwise just wait for strut brace group buy No: 2

We are good to go, shipment is scheduled in for monday. For those of you who still want to purchase a strut brace or 2 the cost will be $65 each + 13 p&h for 1 $20 for 2 or you can pick it up. I will be getting the braces on the weekend so if you want one make sure you get incontact with me soon.

i know its a bit late, but interested in front 33.  

where is pick up from?

live in brisbane

wow what a deal!

but for the fact i was offering these at the same prices (one is 85 del, two are 150 del) with no need to group buy!

ho/hum :)

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...