Jump to content
SAU Community

Recommended Posts

Summary

1997 R33 Skyline GTR Series III

KR4 Silver Metallic (Rare Dark silver)

2.6 litre Twin-Cam Twin-Turbo 24-Valve (220kW @ wheels)

4 wheel Brembo brakes, vented discs, ABS. 4WD, 4WS, PS, PW, Climate Control

Original 17" Forged Alloy Wheels

Nissan Alarm + Quiktrak Security System

Modifications

Power + Drivetrain

Greddy Profec B Boost Controller in CF Panel

Apexi GT Spec Intercooler

HKS Complete Hard Piping Kit

Apexi Power FC

Tomei Aluminium Cam Gears

Cusco Oil Catch Can

ARC Titanium Hood Panel

Nismo Weldina Front Pipe

Trust/Jasma Catback exhaust

Blitz SUS Stainless Steel Airfilter

Nismo Twin Plate Clutch + Nismo lightened Flywheel

History:

This car is a rare private import with full Australian compliance. I sourced this car personally in Japan and it was purchased in standard form from Auction with a Grade of 5 and one previous owner. All servicing in Japan was performed at Nissan Prince Saitama and Nismo Oomori Factory. Servicing in Australia has been primarily performed by Proconcept in Ryde. Receipts can be shown for servicing.

The car has always been maintained maticulously and those who have seen the car can vouch for it. There is no need to perform any servicing or maintenance on the car and it is ready to go. Mechanical checks are welcome. I can personally guarantee this is one of the best example late model GTRs in Australia.

Specs

Standard GTR Specs here:

http://www.gtr.co.uk/html/technical/r33.asp

Additional Series 3 Specs:

Red stitched door trim and seats

Xenon Headlamps

Upgraded front bar with N1 air vents

Upgraded front lips with guided brake cooling ducts

Passenger Airbag

Stiffened Body Shell

Upgraded synchros

Maintenance

Fluids and Wearables

Motul 300V Engine Oil

Motul RBF600 Brake Fluid

Nissan Genuine Oil Filter

Nissan Genuine Fuel Filter

Motul Gearbox Oil

NGK Iridium Spark Plugs

Endless SuperStreet Brake Pads (Front)

RaceBrakes RB74/RB25 Brake Pads (Rear)

Michelin Pilot Sports 265/45/17 all round.

In Car

Nismo 300km/hr Dash

(43 000km showing on Nismo dash and 30 000km on original dash on Nismo receipt)

Greddy 60mm Boost Gauge

Pivot Shift Light

Nismo Shift Knob

Optima Yellow Top Battery

Alpine 9835 MP3 Head Unit

JBL P62 Splits

Pioneer Rear Speakers

Fusion FP1000 Amplifier

Performance

221kw @ wheels on Dyno Dynamics

$44000

Negotiable

Sydney

Email me

0402 092 647

GTR1.jpg

GTR2.JPG

GTR3.jpg

GTR4.jpg

GTR5.jpg

Link to comment
https://www.sau.com.au/forums/topic/57325-fs-1997-r33-gtr-series-iii/
Share on other sites

I remember you.... Your a mate of Franks....

This car is very very nice..... If you are looking for a GTR this is a prime example....

2 thumbs up for the price too.... It will sell quick....

  • 4 months later...

I have been away overseas for the last 6 months but the car is up for sale again. I may be leaving again soon so if you're interested make an offer. I can guarantee this is one of the cleanest R33 GTR's in Australia and numerous members of this forum can testify to that.

  • 1 month later...

*BUMP*

A few serious buyers but all have fallen through.

Consequently car has been placed in this weeks trading post.

This is seriously one of the cleanest R33 GTR's in Australia. Everyone that has come seen it can testify to that. A genuine series 3 with all service logs going back to Japan. I personally owned this car in Japan as well and it has been maticulously maintained in Australia.

Price has been updated to $45000.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...