Jump to content
SAU Community

Recommended Posts

Greg,

Chris is correct,Warren with the white gtr put some on the second to softest compound and he said he cannot believe the difference it makes.Thats on a gtr so one can only imagine what it would be like on a high horse power gts-t.

Regards,

SKYLINE (Kym)....

Link to comment
https://www.sau.com.au/forums/topic/57336-tyre-outlets/#findComment-1107505
Share on other sites

Blackwood Tyrepower is the distrubutor for TOYO's.

They have the cheapest RA1's available as obviously every one has to go through them.

How do the RA1's pull up against the RE55S?

From what I can see the RE55S have more of a semislick aggressive look.

Link to comment
https://www.sau.com.au/forums/topic/57336-tyre-outlets/#findComment-1111222
Share on other sites

The S in RE55S means seriously sticky like sh@t on a blanket. they reduce inherent understeer in the GTR and give better turn in. However the biggest improvement is with the reduction in power on oversteer also inherent bigtime in a GTR. I guess all those with a drift bent would see this as a handicap but those of us who like to chew on everything that goes around corners including motorbikes in the hills there is nothing like them. I bought the WT compound SOFT. There is a SUPER SOFT MEDIUM and HARD. I looked at all the other DOT rated slicks DUNLOP TOYO MICHELIN PIRELLI etc. The Bridgestone is almost half the price of all. This means you can wear out two sets for the price of one. Wish I had of known about the trackday I would have liked to worn them out

DOWNSIDE TO OWNING SEMISLICKS

1. ROAD NOISE

2. MOST OF THE TYRES ENDS UP ON THE CAR

3. NOT GOOD IN THE RAIN

Link to comment
https://www.sau.com.au/forums/topic/57336-tyre-outlets/#findComment-1111793
Share on other sites

In my 15 minute drive to work in the rain this morning my front torgue guage

was wrapped around the endstock and that was just getting out of the driveway.

A couple of weeks of accumulated oil and road grime wasnt helping either. Much more fun and 10 minutes quicker on the way home. One other word about the tyres there is definately less tramlining than with the Falkens I had on before.

Link to comment
https://www.sau.com.au/forums/topic/57336-tyre-outlets/#findComment-1113127
Share on other sites

The S in RE55S means seriously sticky like sh@t on a blanket. they reduce inherent understeer in the GTR and give better turn in. However the biggest improvement is with the reduction in power on oversteer also inherent bigtime in a GTR. I guess all those with a drift bent would see this as a handicap but those of us who like to chew on everything that goes around corners including motorbikes in the hills there is nothing like them. I bought the WT compound SOFT. There is a SUPER SOFT MEDIUM and HARD. I looked at all the other DOT rated slicks DUNLOP TOYO MICHELIN PIRELLI etc. The Bridgestone is almost half the price of all. This means you can wear out two sets for the price of one. Wish I had of known about the trackday I would have liked to worn them out

Where did you buy yours (tyres) from? How much? I do a lot of driving in the hills, and wish to get rid of the understeer problem you mentioned.. I am currently looking at a set of yokies, but if the RE55s are cheap, then I got more money to spend on my engine!!!

Link to comment
https://www.sau.com.au/forums/topic/57336-tyre-outlets/#findComment-1113964
Share on other sites

I had the old RE540s on the R33. They were great in the hills if the roads were smooth, but when they get bumpy & the rest of the time on the street they were such a pain I have got rid of them (of course, they had no tread left anyway!)

I have gone back to normal street yokos. Wont be quite as good for handling, but will make the car much more comfortable to drive.

I used to use Bridgestone in the city when Laurie was there. My last couple of sets came from Mag Wheel centre on Prospect Rd.

Link to comment
https://www.sau.com.au/forums/topic/57336-tyre-outlets/#findComment-1114678
Share on other sites

Sorry for the late reply, been away. I bought them from Bridgestone in Magill Road. They are the only Bridgestone Motorsport Tyre Outlet. Cost was $365.00 each fitted, did notice however they were having a 4 for the price of 3 offer in the EASTERN STATES when I was in Sydney during the week dont know if the same here ask. Even more to spend on your car. BTW cost doesnt change for different compounds in the RE55. I would like to go to a lightweight 18x9 rim, the RE55 comes in a 265/35/18 which wouild increase the overall diameter of the wheel/tyre by 7.6mm just enough to fill the guards a bit more and prevent gutter rash along with 10mm more gripping than the 255/40/17 I m running. The price goes up to $415.00 each.

Link to comment
https://www.sau.com.au/forums/topic/57336-tyre-outlets/#findComment-1118998
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...