Jump to content
SAU Community

Recommended Posts

hi im trying to get a graph up... umm the tuner reckoned he couldnt stop it knocking at 18psi no matter wat he did... thats y its only 16, thats weired aye.. its alittle laggy

Well id be inclined to run a Bosch fuel pump, and run the std manifold. Pinging at 18psi seems a little strange...did he suggest the reson why it was pinging..

he said i should get some plugs a heat range colder...

are u talking about a standard exhaust manifold?

they just cheap weld n grind cams, standard cam gears..

a strange thing is the cas if nearly fully turned anti clockwise (Advanced?)

I would most definitely be checking the cam timing. Ensure it has been setup correctly and then drop a set of adj cam gears on it and see how u go.

How is the power curve when it wants to ping? Does it want to only ping at a certian rpm range? i.e in my case 4000rpm

I have had valve float issues where i bumped boost up and it would always want to ping at 4000rpm + the power curve would go flat from then onwards.

The last I highly doubt. But a few things to look at.

Hey RB power...what is your car like to drive on the streets?

tail happy?

Do you have any suspension/brake mods to match, 238rwkw is alot to stop with standard brakes :woot::blink:

Edited by bigtim11
just quickly....

whats everyone got their rev limiter set at??

since i got the highflow and having full boost at 4000rpm i hit the rev limiter alot!!!

i just dont feel power loss to change gear

street, 6800rpm

track 7500rpm

roy uses a nice rev limit

just quickly....

whats everyone got their rev limiter set at??

since i got the highflow and having full boost at 4000rpm i hit the rev limiter alot!!!

i just dont feel power loss to change gear

LOL...i keep mine at around 8,300rpm. I dont rev 3rd and 4th that hard, but i sure do rev 1st and 2nd gear out to make sure that when i grab the next cog i have as many revs on board as possible. The difference between 4,000rpm and 5,000rpm on my engine is proabably about 100rwkws so worth revving out the lower gears to fall into the meat of the power curve

If your turbo can flow the air, the std cams dotn seem to fall off too abruptly....mine still feels as though its pullign pretty well at 8,000rpm. i thnk it makes about 210rwkws at thoe revs?!?!?!

got the same problem as roy, need to keep the revs nice and high to bypass the lag. mines set at 7500 and is still climbing rather well. cams would definately help but might look at raising it another 300 or so.

i was revving to 8.5 on the old motor before she went.

proly will take the rebuild to a max of 8.3, but this time round with uprated oilpump and valve springs to suit.

gotta remember that rb20's are short oil drive motors so the posibility to destroy the oil pump is very good at high rpms/hp.

Hey RB power...what is your car like to drive on the streets?

tail happy?

Do you have any suspension/brake mods to match, 238rwkw is alot to stop with standard brakes :O:)

hey it seams to be ok alittle loose...lol....stock brakes and suspension apart from lowered springs and drift pinapples lol

my revs are set a 7000 rpm

i was revving to 8.5 on the old motor before she went.

proly will take the rebuild to a max of 8.3, but this time round with uprated oilpump and valve springs to suit.

gotta remember that rb20's are short oil drive motors so the posibility to destroy the oil pump is very good at high rpms/hp.

what year was car? and how many km had it done before it let go?

also, were u driving it everyday at 8000+rpm?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...