Jump to content
SAU Community

Recommended Posts

Well as the title says i got my car on the dyno after suspecting it wasnt running as hard as it should....mods are as follows:

S13 RB20DET

Full 3" Exhaust

Nippon Denso f/pump

POD

FMIC

~11psi

what can i say, power is no where near what it should be! after only just keeping up with a ca18det sil i knew something was up.

Mechanic says all 6 coil packs are failing at once hence the power drop...

he says it should keep climbing to about 140 - 150kw once i get them replaced...

just thought id share it with you ppl, all comments welcome

Joh

Link to comment
https://www.sau.com.au/forums/topic/59081-got-car-dynoed-i-knew-it/
Share on other sites

my god... didn't you hear the aweful popping?!

there is no popping thats the thing, i could only feel that big dip so i knew it had to be something...

Whats with the big arse dip? dud coils would have had your car missing all the way to redline, i wouldn't have expected power to pick back up again that high in the rev range.

i also thought that if it were the coils it would be missing all through the rev range, i must admit it isnt a very smooth curve so then it leads me to think maybe it is the coils playing up??? i dunno, i dont wanna fork out $600 odd just to find out its something else... but the mechanic says its the coils

anybody else think it might not be coils?

11psi I think you will see 130-140rwkw.

15psi with stock fueling see's around 155rwkw, sort out the fueling and you then see around 165rwkw. Replace the ecu and you will see just over 170rwkw.

Get an RB25 turbo and you should get close to 185rwkw.

11psi I think you will see 130-140rwkw.

 

15psi with stock fueling see's around 155rwkw, sort out the fueling and you then see around 165rwkw. Replace the ecu and you will see just over 170rwkw.

 

Get an RB25 turbo and you should get close to 185rwkw.

I would have thought 15psi and the exhaust wheel ends up sitting in the cat...

when you say sort out the fueling what do you mean? injectors? i already got a fuel pump...could you please elaborate?

i plan on a remap and rb25 turbo later down the track....

  • 2 months later...

yeah, dont boost stock turbo too much, ceramic turbine will crap itself. it's ok on s13's which have steel turbines, but be careful with that ceramic sh1t

so, did u locate the problem before replacing your coil packs? or do u have some new coils u need to offload?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...