Jump to content
SAU Community

Recommended Posts

Hi ppls.

I've ran in to an injector problem and have had to get another set cleaned up and the old set that are stuffed ripped out.

I am after a place in SA that do a good job for a decent price.

Let me know if you know of some one and have had experience with them.

Hi ppls.

 

I've ran in to an injector problem and have had to get another set cleaned up and the old set that are stuffed ripped out.

 

I am after a place in SA that do a good job for a decent price.

 

Let me know if you know of some one and have had experience with them.

CARBURETER SALES & SERVICE (S.A.)

6 Little Rundle St Kent Town 5067 (08) 8132 1465

Fax Kent Town 5067 (08) 8363 6373

I think his name is John, cleaned my GTR injectors and got them flowing within 2% of eachother. He gave the terminals a clean as well, made sure everything was 100%

From memory it cost me less than $150, I think it was about $130

:) Chris

got my injectors cleaned at sprints fuel and carburettors

on bridge rd, next to the hyundai car dealer.

Cost me about $120 including new o-rings.

hope this helps.

Shaun

had the car in tilbrooks cause the car was leaning out.

Thought it was the fuel pump, but replaced that and

still found that i had the same problem. Then borrowed

a standard set of injectors from tillbrooks and got them

cleaned and the car still ran lean when i put them in.

So they think my computer has been chipped, but my

car was stock when i bought it so i have a problem

that no one can figure out.

That's why i got my injectors cleaned.

the fuel pressure reg is now been squished to hold pressure.

this brought the fuel map down .3. From 12.3 to 12, tilbrooks

said it wasn't the problem, its got everyone scratching their heads.

if i don't sell the car i will be putting an ajustable fuel pressure reg

on the car, will see if this makes a difference. I will also be checking

the computer for a chip. :P

i had my vl turbo ones done at mildren race engineering.

they are a bit more expensive than some places (because they charge extra for o-rings or new pintle caps) but they did the best out of the 3 places i've been to.

i had two other sets for my previous cars cleaned at other places (one near city dismantlers and one in lonsdale) and both times after the clean the cars were harder and required more cranking to start, which is apparently an indication of leaking injectors (and the puff of black smoke one of them blew after every startup confirms that).

  • 2 weeks later...
CARBURETER SALES & SERVICE (S.A.)      

 6 Little Rundle St Kent Town 5067  (08) 8132 1465                

 Fax Kent Town 5067  (08) 8363 6373  

I went through these guys to flow test, clean and re-flow test some injectors I might put into my FJ20, I requested a before and after so I could see the difference of what the clean did, they also replaced the pintle bits and o-rings and another rubber that sits near the top of the injector in the price, $25 per injector, extra if you need them to take them out of the fuel rail for you.

The only thing that disappointed me was the fact that they couldn't tell me how many cc/min the injectors are good for! Which to me seems a pretty basic thing, they do however give you details on how fast it flows a certain amount of volume, so from that you can work out the approx cc/min of the injectors based on the pressure they feed them at.

It's $20 per injector if you only want them cleaned and flow tested.

Cheers,

fj910

it was worth the money for the peace of mind i suppose, turns out they werent badly blocked or anything. the spray pattern is just hand drawn so in my case it didnt show any difference. however the flow rates were all the same after and they did vary a bit before.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...