Jump to content
SAU Community

Power FC help - needed before Friday 7 Jan!!

Ronin 09

By Ronin 09,
in Engines & Forced Induction

 Share

Recommended Posts

Ronin 09 Grand Master

Ronin 09

Posted
Posted

Hey Guys,

I'm in Japan at the moment and have found a second hand parts store that has a Power FC for my car (BNR32) for around 600 dollars with controller.

I have a few questions -

1. the serial number is PFC RB26 9605-0387. Is there any way of telling how old it is? it looks to be in very good condition...

2. in my very poor japanese / english translations, the guy said that there was no maps on it... my question is- do all PFCs have a 'base map' that cannot be erased? I don't want to buy it and find that it has to be programmed from scratch.

Thanks for your help in advance!

BTW - i was like a kid in a candy store!! If anyone ever visits Japan, make sure you find an 'Up Garage'!!

cameron Mentor

cameron

Posted
Posted

Hi Marcus,

I always thought that the FC came with base maps. - Inless its you'r translation :wassup:

If the maps were deleted using the PFC laptop software this wouldn't save on to the FC it self could it ? Maby thats whats been done :uhh: Ask the bloke if you can install it into another car their and try it, or is that not possible ?

:D

Jun

GTRgeoff Grand Master

GTRgeoff

Posted
Posted

And grab me a cheap hand controller for the R33 GTSt mate :rofl:

I understood the base maps were always there, but be cautious of the PFC being password locked. Good idea to get them to demonstrate if possible.

Ronin 09 Grand Master

Ronin 09

Posted
  • Author
Posted

Cameron / Geoff: they can't demonstrate as there are no 32GTRs there... the rough translation of the characters on the box is 'signal / data check before use'!!!

don't think it is password locked...

might just hedge my bets and get it and see...

Beer Baron Grand Master

Beer Baron

Posted
Posted

my advice would be to just but a brand new one. it's not worth as much if it's not the latest revision. The early ones can't be used with FC logit and the later ones apparently have some firmware upgrades too. unfortunately the only way to check is to plug it into to a 32 or 33 GTR and see what version it is. I say just buy a new one, unless you're confident of what it is.

Richard

GTRgeoff Grand Master

GTRgeoff

Posted
Posted

Marcus, cheers mate. Anywhere up to $150 or so will be fine....and maybe a long cable, and don't forget to add some extra for your trouble, like a carton of cold ones :D

It should be OK if it isn't password locked, so then you can still tune it at least. Highly recommend driving as little as possible/very gently if using the base map.

Ronin 09 Grand Master

Ronin 09

Posted
  • Author
Posted

Geoff: went to the Up Garage again today, seems as though all the hand controllers are sold with the respective PFCs... sorry about that.

B1: the Up Garage I went to is... either the Kawasaki or Hiratsuka Tokkaido store... not sure which one but know how to get there. It isn't very big, but main reason I went there because it is on my g/f's house train line. There isn't a heap of stuff there.

Suspension isn't a heap cheaper than second hand stuff you can get from people off the forums, plus it is damn heavy to ship over.

I decided that the plastic has taken enough of a beating (bought a EVC-R today), so will get a new Power FC from Nengun when I get back and have some $$ :Oops:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...