Jump to content
SAU Community

Recommended Posts

Hey im planning on getting an R32 gtst for a drift car..

i will be putting in an rb25det manual.

so could i just get an auto r32 gtst?

is the only difference between auto and manual the gearbox etc..

are the breaks the same, (i think its only non turbo and turbo that are different for the breaks?)

any interior differences?

thanks all!

sigh....

brakes are the same, although as an auto may be less optioned as it may more likely be used just for transport. i.e. you may have a greater chance of getting the "non type m" (single pot) brakes... which I have in mine.

interiors are the same from what I've seen.. below the dash cluster on the R32 there is the current gear indicator, but its not part of the speedo cluster like R33. This will stay in the console if you convert it to manual just not work.

You have got a coupe of buttons on the inside console for "power" and "snow" mode or some crap. Thats about it as far as I can tell. When you remove the center gearshift surround, that will all go.

Think they're all still LSD's.. the autos have a shorter diff ratio, which is nicer for acceleration.

I think I saved about $2k by not getting a manual (of unknown condition).. and when it comes time to convert hopefully you'll be going for brand new clutch, reconditioned clutch cylinder, and a gearbox you know will be in nice condition.

Oh yeah, the ECU's will be different.. however generally the auto ECU will run manual fine, just not vice versa.

You can look on my site if you like for pictures if that helps.. one dead-stock auto...

thanks for that.. auto it is then..

another thing.

how much will a fresh rb25det cost + installation? ive been told around 4.5k all up?

also i would be better off getting the car complied AFTER the conversion? or before the conversion?

if its under the 15 year rule you might as well comply it after the conversion afaik , as any road worthy issues with the old engine/gbox would need to be fixed for compliance and that money you obviously dont want to spend .

but considering a front cut rb25det 5 speed is about 5k your going to be spending alot more that 4k! id say 6-7k if a workshop is doing it . if you do all the work yourself and get money back for your old bits it might come in under 5k . but budget for the unexpected to happen , it always does

My Auto R32 is a couple of days away from being on the road. I'm gonna be converting it within a few months to an RB25 manual box (possibly, still undecided). I'm only gonna be slightly working it (between 200 and 250rwkw) so hopefully that should hold her. But yeh, virtually negligible differences - get the auto :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...