Jump to content
SAU Community

Recommended Posts

ive got a RB30DET in my r32 gtst. Its got a stock vl bottom end, but with a r32 gtst oil pump. After doing high speeds and reving it out to 7000rpm, my car started to make knocking noises about 10 mins later after just cruising at 110km along highway. I noticed a little drop in oil pressure. The knocking noises got worse as i slowed down and stopped. When i started it up again, it was knocked really bad.

We took the motor out and pulled it apart, to notice that one of the big ends was down to the metal, and the two shells had been rolling. Another one was down to the copper. When bearings went in the, clearances where all good.

Just wanted to know if anyone knew why they failed. Could it be that the oil pump is not pumping enough oil the the bearing at high revs and speeds, or maybe some dirt got into it?

Link to comment
https://www.sau.com.au/forums/topic/61465-rolled-a-big-end/
Share on other sites

I thort the RB20DET Oil pump was a NO NO on an RB30DET combo.

How many k's did you put on the engine before you gave it this kinda treatment ? i gave mine about 5000k's before i really gave it a flogging like that and now 5000km later after many races and revs up to 7000rpm its still running fine.

Im running stock bottom end with ACL bearings but with RB25DET oil pump.

I could be wrong but I think the RB25DET oil pump flows much more.

Link to comment
https://www.sau.com.au/forums/topic/61465-rolled-a-big-end/#findComment-1161418
Share on other sites

I am thinking that the car has got 330rwhp - give or take a few hp.... It was dynoed before at 310rwhp on 9psi and now its using about 13 so *shrug*

Lack of oil can do that damage to your bottom end and alot more :) but it could even be the tuning that caused it or even a rattle. You just never know. I would invest in a RB25DET oil pump this time just to be sure.

Link to comment
https://www.sau.com.au/forums/topic/61465-rolled-a-big-end/#findComment-1161606
Share on other sites

Guilt-Toy,

Where did you hear the RB20t oil pump was a no no?

Quite a few ppls on the calaisturbo forums simply use the RB30et pump that flows less than even the rb20t pump and they haven't had any issues.

I think it really comes down to the rebuild. If it has been done properly, all it takes is to have some gunk in the block (due to the builders not cleaning properly) and you will stuff the motor.

The fact is the rb20det pump is designed for the high rev's. RB30 pump is not, so there should not be any problems with oil starvation.

That being said I think the RB25det pump is quite a bit better. Oil pressure is up quite a bit over the rb20t. On cold starts its always on the 8 or slightly higher. Once the oil is warm it sits on the first line (2) then cruise it sits just above 4 and once reving its up around 6.5-7. On the stock guage.

Was there any tell tale signs before hand? slight knock on cold starts etc?

Oil overheated caused bearing failure?

Just a few really quick questions that may help others.. :)

What oil are you using? What oil filter?

What brand bearings? Mains & Bigends?

Was the motor Balanced?

Any modifications to the head oil restrictors in the block?

Was the oil pump pulled apart and clearances checked? (they are getting on now)

Link to comment
https://www.sau.com.au/forums/topic/61465-rolled-a-big-end/#findComment-1162002
Share on other sites

Just so ppls know in comparison to their motor..

I've got forgy's that run a fairly large 0.004" I think it is clearance.

On cold morning starts they knock a little for the first couple of seconds then have a really light knock until the oil pressure drops (oil is warm) and pistons have expanded. Once warm it is silent.

The knock/slap can only be heard when standing right next to the car.

I tend to like the knock/slap actually. :) At first I thought it was the head and had it checked out.

I don't use a drop of oil (which is suprising considering the bore clearance).

It used quite a bit in the first 1000km's but then all of a sudden cleared up and now literally doesn't use anything.

I'm curious as to how some others have had experience with their motors.

In the 6000km's I've traveled I've done 4 oil changes.

Link to comment
https://www.sau.com.au/forums/topic/61465-rolled-a-big-end/#findComment-1162008
Share on other sites

R32 GTSTT, sorry to hear of your engine failure. while at this time I don't have any extra points to add over the other good advice given, I, and I'm sure many others, would appreciate and benefit if you posted details of your engine failure in the thread in my sig.

:)

Link to comment
https://www.sau.com.au/forums/topic/61465-rolled-a-big-end/#findComment-1162011
Share on other sites

A common cause of conrod bearing failure that hasn't been mentioned is detonation. Have a look at the top half of the other conrod bearings and see if they are marked from say 10:30 to 2:30 (if the big end bore of the conrod was a clock with the piston sitting straight up, looking at the front).

Marks here are a fair sign that the engine has been detonating and it would be worth playing with the tune when you get it going again, taking out a little timing or putting in a little more fuel.

Just a thought anyway.

Link to comment
https://www.sau.com.au/forums/topic/61465-rolled-a-big-end/#findComment-1172977
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
×
×
  • Create New...