Jump to content
SAU Community

Compliance workshop troubles

stingray
 Share

Recommended Posts

stingray Collaborator

stingray

Posted
Posted

I just got my car back from the compliance workshop today and I took a look at it. The back child anchor points isn't even put in. The bottom plate has been secured underneath the parcel self but the actual anchor hook thing isn't screwed in from the top. By the looks of it they have drilled behind the speaker grill and then they realised that the anchor points won't fit behind there and just left it as it is. Also they have drilled one of the anchor points off centred. How much can it be off centred? They have also drilled from the bottom up and obviously hit the window because now there is a scratch mark in my rear tinting on both sides. Is this unavoidable as drilling upwards is hard or should I go back and see what they say?

Link to comment
https://www.sau.com.au/forums/topic/61486-compliance-workshop-troubles/
Share on other sites
GTR V Enthusiast

GTR V

Posted
Posted
I just got my car back from the compliance workshop today and I took a look at it. The back child anchor points isn't even put in. The bottom plate has been secured underneath the parcel self but the actual anchor hook thing isn't screwed in from the top. By the looks of it they have drilled behind the speaker grill and then they realised that the anchor points won't fit behind there and just left it as it is. Also they have drilled one of the anchor points off centred. How much can it be off centred? They have also drilled from the bottom up and obviously hit the window because now there is a scratch mark in my rear tinting on both sides. Is this unavoidable as drilling upwards is hard or should I go back and see what they say?

Well you can't drill down unless you remove the rear window

stingray Collaborator

stingray

Posted
  • Author
Posted

Yeh i kind of figured that he will have to drill up and its unavoidable so i'm not so worried about that. What's worrying me is how close to the centre of the seating position the anchorage point has to be because I remember hearing it has to be within a certain area near the centre position. Does anyone have pictures of how their's is done?

predator Grand Master

predator

Posted
Posted

yeah, i just did mine..

as close as possible to the centre of the seating position, but like you say thats nigh impossible because of the speaker holes... but it had to sit a fair way back as the speaker holes are in the way.

I rivetted twice each point to hold the bracket in.. sits just behind the speaker cutouts (I had no speakers). And even if I do say so myself, I did a ****ing awesome job :-D

Will post a pic next copule of days for you..

ylwgtr2 Grand Master

ylwgtr2

Posted
Posted

to do the job right you need to make up brackets that bolt to the shelf and protrude up to clear the speaker then back down again and bolt down to the shelf .....these are supposd to go directly behind the headrest's

GTR V Enthusiast

GTR V

Posted
Posted
Yeh i kind of figured that he will have to drill up and its unavoidable so i'm not so worried about that. What's worrying me is how close to the centre of the seating position the anchorage point has to be because I remember hearing it has to be within a certain area near the centre position. Does anyone have pictures of how their's is done?

I was told within 40mm of the centre of the seat

FLO Collaborator

FLO

Posted
Posted

In my opinon marks in the back window is lazy. You have to drill up, but just use a short drill bit or use some timber as a depth control. All these places charge top dollar and just slap em through. I would take it back. If you want something done right just do it your self.

predator Grand Master

predator

Posted
Posted

well there must be some conjecture.. as I have seen them both right behind the seat, and right behind the speaker holes (i.e. right back towards the glass).. so there must be some different interpretations... Either way they're being passed with both.

I just copied GTR V's points (thanks again), as his got through fine. I hope mine are in the right position, as buggered if I want to do them again!

I think the key is the "centre of the seating position" rather than how far back they are... because i have seen them in the two positions regularly.

I don't know how you could manage to scratch the glass, but you'd have to be trying pretty hard.. and using the world's longest drill bit.

predator Grand Master

predator

Posted
Posted

like duncan says.. not a bad idea .. if its SEVS its the workshop's responsibility to get it right.

Anyhow, took a few pix of mine..

the first photo shows how its rivetted in. Hopefully I've done it right, as I'm just playing it by ear here.. Its very solid.

The 3rd shows the positioning there.. I built another parcel shelf, and to hide the ugly speaker holes until i get some in the back there.

You can see in the 2nd photo in the another car I just picked up over the weekend. Interestingly enough on that one, points are back rather than right up against the seat.. yet in my mate's GTR they are right up against the seat. Its almost like 50/50.

So bah, who knows.. we'll find out when i meet an engineer.

stingray Collaborator

stingray

Posted
  • Author
Posted

It's under 15 year old rule. I'll try to get some pics to show you. Thanks for your pics predator, mine is wayyyy back against the back window. They drilled through the edge of the speaker grill so there a hole there that I can just feel when i reach all the way back. My tinting is very dark so I don't know how I'm going to take the picture from the outside, but I'll work something out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...