Jump to content
SAU Community

Recommended Posts

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

Damn... wish you guys had 4WD dyno, Lumpy did a Beautiful job on my tune for the 180, now the GTR is being tuned elsewhere.. Not my call though..

I hate living in the sticks otherwise I would be in for a tune after the next round of mods..

Damn... wish you guys had 4WD dyno, Lumpy did a Beautiful job on my tune for the 180, now the GTR is being tuned elsewhere.. Not my call though..

I hate living in the sticks otherwise I would be in for a tune after the next round of mods..

Why??

we can tune GTR's in 2wd mode. Has no adverse affect on either the car or the result..

Cheers

ken

A GTR is a full time rear wheel drive car with computor controlled split to the front and running one on a 4WD dyno means it must drive the front wheels the whole time its on the dyno and that is a very un natural situation for a GTR so dont panic about putting them on a 2wd dyno.

Damn... wish you guys had 4WD dyno, Lumpy did a Beautiful job on my tune for the 180, now the GTR is being tuned elsewhere.. Not my call though..

I hate living in the sticks otherwise I would be in for a tune after the next round of mods..

ha mate if you love your R like i do i would be sending it to the best tuner i know and Lumpy the man ,ran mine yesterday to check the afms(z32) that we installed and ran a lazy 529.4rwhp at 20psi even in the limited time we had to do so and just to watch the guy in action is impressive.

pete :D

ha mate if you love your R like i do i would be sending it to the best tuner i know and Lumpy the man ,ran mine yesterday to check the afms(z32) that we installed and ran a lazy 529.4rwhp at 20psi  even in the limited time we had to do so and just to watch the guy in action is impressive.

pete :P

do you mean you can actually watch it get tuned ? last time i was at hyperdrive ken shoo-ed my out of the workshop !

Yes for occ. health, safety and insurance reasons, everyone other than staff must be out of the workshop area in the designated viewing area. If something lets go, its bad enough mopping up the motor let alone the bodies!

I think Bart snuck a peek at the action on his way to either get another, or loose another bourbon.........

nah not the police

but you wouldnt read about it on freeway heading home a basic std s13 wanted a go well forgot it was still in 2wd and well it lit up at 115km for abit before we hose the p plate silly boy silly boy ,he must have got bit of a shock

ooppps this is bit off subject sorry

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...