Jump to content
SAU Community

Recommended Posts

I got falken ziex 265/35/18 on the rears I find then realy good in the dry but in the wet i think they are just crap i was told thay had a high temp rating and in the wet they struggle to get heat in to them thus no traction cheers.

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

if you want good rubber go and see if you can get some Re55s but they come at a cost and they a an import tyer. last i got them for was $480.. or you can do the top of the range Falken's and pay $525 for 275x18x35 for the rear...that's each by the way .. i have Falkens on the rear of mine great tyer but do not do to many burnout's ..

Falken 326 must be the most common skyline tyre out there....compliancers put them on because they are cheap and come in big sizes. They are terrible.

Falken ST115 are also appalling, which is even worse when you think they promote them as sporty.

Falken FK451 on the other hand are excellent tyres....go for em if you can get em, about $450 each.

For Re55s, they are brillian but will wear really quickly, 5-10000klm only. SAU NSW club members can get them in 17s for about 400 a corner from Gordon Leven

They are probably a little worn as well .

Any car with wide tyres at the front will tram to some extend , i got 265 's it trams too , it even trams with the stock 245's but not as much .

i just changed from some of the old Michelin pilot SX (not available now) and everyone i spoke to said Yoko C-drives were the Sh!t, and that once i used them id never use another tyre. Well thats the biggest load of crap!

unfortunately i did little research and just got the C-drives. Soon after learn that they replace the A539's, which while good, are never going to be michelin pilots!

These tyres ride super quiet, and are really comfortable, but on hard braking they lock up much easier than the pilots. Turn in and bite is far less positive, and on fast sweepers the car seems to subtly creep out and not hold the line.

Im not saying the C-drives are bad tyres, but when comparing them to a tyre such as a pilot then you see why you pay so much for the michelins.

while you can find performance tyres on a budget, the "best street tyres" will always be the most expensive each company has to offer! eg, im sure if you can foot the budget you wouldnt be disappointed with top level yoko AVS's, Pilot Sports, and Bridgestone Potenza's.

i saw someone mentioned yoko AVID S306's as good tyres! Sorry but have to disaggree! they are good if you like quiet tyres, but not if you like grippy tyres. I ran a set to about 50% then changed them for some potenza's. Bottom line, S306's are yoko's bargain "ECONOMY" passenger car tyre. Not what you want if you drive a car with some power. very easy to brake tracktion and lock up under braking.. these were on 19's, so probably exacerbated by the ultra low profile.

The latest Wheels mag tests a variety of tyres and the performance tyre which one was the Goodyear Revspec RS-02.

http://www.goodyear.com.au/passenger-tyres.htm

The Michelin Pilots came in a close second. From memory these tyres have either won or come second in every tyre test by Motor and Wheels over the last few years. Of course they cost plenty.

I wanted to try the Revspec on my Peugeot 205 GTI but they don't come in my size (195/50/15). I currently have Dunlop FM901s on my grey GTR and have to buy some new tyres to fit the R34 GTR rims I've got for the white GTR. Don't know the cost of the Goodyears yet. I'll make some calls and post the results.

Re the Kumho Ecsta's........ OK so most everyone thinks that they're sh!t but in what way ? And what version ? 711, 712 etc ?

I guess I'm asking are they OK for cruising and the ocasional belt down Putty Rd ?

Re the Kumho Ecsta's........ OK so most everyone thinks that they're sh!t but in what way ? And what version ? 711, 712 etc ?

I guess I'm asking are they OK for cruising and the ocasional belt down Putty Rd ?

well we used to run the khumo 711 on the daewoo race cars, and the 712s in one enduro as well. They were good tyres, I'm not sure of how the price compares (we were paying $250 for 205/16s) 711s about 2 sec better than the 712s around wakefield.

well we used to run the khumo 711 on the daewoo race cars, and the 712s in one enduro as well.  They were good tyres, I'm not sure of how the price compares (we were paying $250 for 205/16s)  711s about 2 sec better than the 712s around wakefield.

HOLY CRAP !! $250 for 205/16's ?!?!?! :crazy:

Is it just me or is that a lot of $'s for a little hoop ?!?!

So what would I be looking at for 255/40/17's ( I think the ones I'm looking at are Ecsta MX KU15 ) ?

At the moment I'm on Falken ZE512's that cost $250ea for 255/40/17 and $150ea for 235/45/17.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...