Jump to content
SAU Community

Recommended Posts

Similiar to what happened to my sisters VL after the flush.

Only difference was before the flush it wasn't overheating, after it was. :cheers:

I pulled the radiator out and when reverse flushing with compressed air and water I had what felt like bark chip covering my hand. It was massive bits of scale that had blocked the core. :(

That may be the case. It might not be the head but how pissed would you be if you spent all that money doing all this other 5hit and then find out it was coz a fake mechanic couldn't do a simple test.

How does he know it's not. Has he got Xray vision or something. A dye test will pick up the smallest leak that won't even cause your car to overheat.

Well anyway, I'm done with the advise. If you choose to ignore it, that's your choice. Like I said before, it may not be the head. I hope it isn't. I hope it's something simple to fix because I have gone through all of it hundreds of times. I just believe that it is best to cover all bases so that you rule out all possibilities. To say that it is not a particular problem without performing the tests to prove it is just foolish. I really hope they do the right thing by you.

Well i like to say 3LIT3 FORS3 WAS right.... and i should of done he sed...!!

it was a blown head in my engine !!! ****en bullshit !!!!!!!!!

so now i got a quote from ADD racing to get it done for 1200

wat do u guys reckon of that price??? any places in brisbane that will do it cheaper ???

and what does it inovole wen changing a new head ?????? pullin the engine out ???

You would get change from $800 if you did it yourself. Plus without knowing the condition of the head it is impossible to give an accurate quote as if the head is bent it will cost $600 to get a full head service and straightened. Now I'm sure even if you got the $450 VRS set for free, you would still not get away with $800.

Worst case scenario is:

Full head service $600

VRS $450 (assuming you can buy the VRS seperate from the full kit which is $600)

Labour - 9 hrs - $500

Oil and filter change - $50

Coolant - $30

Timing Belt - $80

Plus you have to account for broken exhaust studs, hylomar spray and any vacuum lines or hose clamps that may break while doing the job.

Total worst case scenario is: $1730 approx

If you can get a second hand head that is already straight or the head you have is still straight, the price would then drop to $1250 plus the cost of the second hand head if so required.

If you do it yourself you would save the $500 labour so then it would drop to $750 for a straight head and $1230 for a bent one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...